Manual Teka IR 642 (page 12 of 25) (English, German, French)

781079

Zoom out

Zoom in

1/25

being installed, care should be taken in

case there is any protruding part or

sharp edge which could cause injury.

When installing units or applian-

ces above the hob, the hob should be

protected by a board so that the glass

cannot be damaged by accidental

blows or heavy weights.

The glues used in manufacturing

the kitchen unit and in the adhesive on

the decorative laminate of the worktop

surface should be made to tolerate tem-

peratures of up to 100ºC.

TEKA assumes no responsibility

for any malfunction or damage caused

by faulty installation.

PLEASE REMEMBER THAT THE GUA-

RANTEE DOES NOT COVER THE

GLASS IF IT SUFFERS A VIOLENT

BLOW OR IF IT IS USED IMPROPERLY.

Fastering the hob

When the gap has been properly sized, the

sealing washer should be put on the lower

face of the glass. Silicone should not be

applied between the glass and the unit

worktop because if it becomes neces-

sary to remove the hob from its position,

the glass could break when trying to

detach it.

To attach the cooking countertop to the fur-

niture, a set of clamps are supplied that

should be fastened in the existing holes in

the lower part of the framework. There are

two possibilities of where the brackets may

be placed, just as is shown in figure 2.

Depending on the thickness of the cabinet, it

may be necessary to use the self tapping

screws that are provided as compliments for

securing; insert them in the circular holes of

the bracket. The thread of this hole will be

made when the screw is inserted inside of it.

The thread should be made before faste-

ning the bracket to the hob.

Connecting the electricity

The electric connection is made via an

omnipolar switch or plug where accessible,

which is suitable for the intensity to be tole-

rated and which has a minimum gap of 3

mm between its contacts, which will ensure

disconnection in case of emergency or

when cleaning the hob.

The connection should include correct ear-

thing, in compliance with current norms.

If the flexible supply cable fitted to these

appliances ever needs to be changed, it

should be replaced by TEKA’s official service.

The input cable should not be in contact

either with the body of the hob or with the

body of the oven, if the oven is installed in

the same unit.

When using the hob for the first

time, please take care not to have

powerful halogen lights, like those of a

hood, shining over the sensor button

area of the hob. These lights may inter-

fere with the starting of the system.

Sealing washer

fig. 2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Teka IR 642 in the language / languages: English, German, French as an attachment in your email.

The manual is 0.86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Teka IR 642 Manual

Product: