529594

Teka HPE 735 Manual

15
Zoom out
Zoom in
Previous page
1/25
Next page
29
ENGLISH
28
INCIDENTS WHEN OPERATING THE PYROLYTIC FUNCTION
INCIDENT CAUSE SOLUTION
My accessories and shelf
supports are damaged.
You have not removed the
accessories and supports during
the pyrolytic cleaning cycle.
You must replace them and
remove them in later cleaning
cycles.
The enamel colour has
changed and stains have
appeared.
The chemical composition of
some foodstuffs may cause
changes in the enamel.
This is normal and does not
damage the properties of the
enamel.
The oven door is locked, pilot
light is lit up but the oven
is not hot.
You have turned the control
dial to position and no
other additional operation has
been performed.
Switch off the oven and follow
the instructions to unlock the
door in the first 30 minutes at
a low temperature.
Next, select the pyrolytic
function, carefully following the
instructions.
I have turned the control dial
to position , pressed the
PIRO
key, I can see the P1,
P2 or P3 on the display but
the pilot light is not lit up
and the oven is not heating
up.
The oven door is not closed
properly, so the door cannot
be locked.
Check the door and make
sure that it is closed properly.
I have turned the control dial
to position , pressed the
PIRO
key, I can see the P1,
P2 or P3 on the display but
the pilot light is not lit up
and the oven is not heating
up.
The door switch is not working
even though the door is
properly closed.
Call Technical Assistance
Service as there is a fault in
the door switch.
I have programmed the
pyrolysis function, the oven is
working properly but pilot light
is not lit up.
Pilot light does not work
properly.
Call the Technical Assistance
Service.
The pyrolysis programme has
ended and the oven is cold,
but the door is locked and
symbol is flashing.
You did not turn the control
dial to position when the
pyrolysis programme ended.
1. Turn the control dial to
position and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position again and wait
until pilot light turns off.
4. Press the
PIRO
key for 3
seconds.
INCIDENT CAUSE SOLUTION
The control dial is in position
and the door is still locked.
The oven has not cooled down
to the safe temperature.
Wait until the temperature
lowers and pilot light turns
off. Then, cancel the pyrolysis
programme.
The control dial is in position
, the oven is cold and the
door is still locked.
You have not followed the
instructions to cancel the
operation correctly.
1. Turn the control dial to
position and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position again and wait
until pilot light turns off.
I have put the control dial in
position and the door is
unlocked, however symbol
is still lit up and the
remaining time of the cleaning
cycle can be seen on the
display.
You have not followed the
instructions to cancel the
operation correctly.
Follow the instructions to
cancel the pyrolysis
programme.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka HPE 735 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka HPE 735 in the language / languages: English, German, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info