Manual Teka HPE 635 (page 15 of 25) (English, German, French, Portuguese, Spanish)

529595

Zoom out

Zoom in

1/25

ENGLISH

INCIDENTS WHEN OPERATING THE PYROLYTIC FUNCTION

INCIDENT CAUSE SOLUTION

My accessories and shelf

supports are damaged.

You have not removed the

accessories and supports during

the pyrolytic cleaning cycle.

You must replace them and

remove them in later cleaning

cycles.

The enamel colour has

changed and stains have

appeared.

The chemical composition of

some foodstuffs may cause

changes in the enamel.

This is normal and does not

damage the properties of the

enamel.

The oven door is locked, pilot

light is lit up but the oven

is not hot.

You have turned the control

dial to position and no

other additional operation has

been performed.

Switch off the oven and follow

the instructions to unlock the

door in the first 30 minutes at

a low temperature.

Next, select the pyrolytic

function, carefully following the

instructions.

I have turned the control dial

to position , pressed the

PIRO

key, I can see the P1,

P2 or P3 on the display but

the pilot light is not lit up

and the oven is not heating

up.

The oven door is not closed

properly, so the door cannot

be locked.

Check the door and make

sure that it is closed properly.

I have turned the control dial

to position , pressed the

PIRO

key, I can see the P1,

P2 or P3 on the display but

the pilot light is not lit up

and the oven is not heating

up.

The door switch is not working

even though the door is

properly closed.

Call Technical Assistance

Service as there is a fault in

the door switch.

I have programmed the

pyrolysis function, the oven is

working properly but pilot light

is not lit up.

Pilot light does not work

properly.

Call the Technical Assistance

Service.

The pyrolysis programme has

ended and the oven is cold,

but the door is locked and

symbol is flashing.

You did not turn the control

dial to position when the

pyrolysis programme ended.

1. Turn the control dial to

position and wait for 1

minute.

2. Turn the control dial to

position and wait for 1

minute.

3. Turn the control dial to

position again and wait

until pilot light turns off.

4. Press the

PIRO

key for 3

seconds.

INCIDENT CAUSE SOLUTION

The control dial is in position

and the door is still locked.

The oven has not cooled down

to the safe temperature.

Wait until the temperature

lowers and pilot light turns

off. Then, cancel the pyrolysis

programme.

The control dial is in position

, the oven is cold and the

door is still locked.

You have not followed the

instructions to cancel the

operation correctly.

1. Turn the control dial to

position and wait for 1

minute.

2. Turn the control dial to

position and wait for 1

minute.

3. Turn the control dial to

position again and wait

until pilot light turns off.

I have put the control dial in

position and the door is

unlocked, however symbol

is still lit up and the

remaining time of the cleaning

cycle can be seen on the

display.

You have not followed the

instructions to cancel the

operation correctly.

Follow the instructions to

cancel the pyrolysis

programme.

j'ai besoin du schéma de principe du four teka hpe 635 Submitted on 11-4-2021 at 17:52
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Teka HPE 635 in the language / languages: English, German, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Teka HPE 635 Manual

Product: