781321

Teka EWH 50 VE-D Manual

47
Zoom out
Zoom in
Previous page
1/58
Next page
Fuction
ECO mode
Factory setting parameters
55
°C
Basic parameters of system of factory setting
With the system switched off, press the “ECO” and “ON/OFF” keys for 3
seconds and the indicator lights will all go on. And then, the system shall enter
into factory setting mode. 2 seconds later the system will enter into
“Heating/Heat preservation function” state. See the following table for Factory
setting parameters.
7
5. Restore factory settings
②
④
⑤
Temperature information area
“-” key, adjust the setting temperature：
The temperature can be adjusted pressing the “-“ key. Every click will
reduce 10ºC the temperature setting (75-65-55-45-35).
③
“+” key, adjust the setting temperature:
The temperature can be adjusted pressing the “+“key. Every click will
increase 10ºC the temperature setting (35-45-55-65-75).
“ECO” key:
When the unit has been switched on, press the “ECO” key to enter into the
“ECO” mode. Press “-,+” key and the indicator light of actual temperature
shall go out in order to highlight that the temperature is not adjustable in
the “ECO” mode. The indicator light of 55ºC will flash for 5 seconds later
and then the indicator light of the actual temperature will go on.
Press the “ECO” key again to restore the previous temperature setting.
Press this key for 3 seconds to enter into the SMART CONTROL mode.
The pilot light indicator flash successively around temperatures when the
SMART CONTROL is activated. Press SMART CONTROL bottom for 3 seconds
to exit the SMART CONTROL mode and restore to the previous mode.
a.
b.
after entering the factory setting, press the ECO key again and the
temperature is still 55ºC, because the factory setting parameter is the
default 55ºC (ECO’s temperature is the same as the factory default
temperature)
NOTE
When a dry burning fault occurs, the 3 indicator lights 35, 55 and 75 will flash
at the same time; in case of over-temperature fault, all 5 indicator lights will
flash at the same time; when disconnection or short-circuit of sensor occurs,
the 5 indicator lights will flash from left to right. At this time, all the relays will
be disconnected and the keys will not work. After the fault is removed and the
6. Alarm and fault self-test
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka EWH 50 VE-D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka EWH 50 VE-D in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 0.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info