781317
38
Zoom out
Zoom in
Previous page
1/45
Next page
1.
2.
3.
4.
The supply socket must be earthed reliably. The rated current of the socket
shall not be lower than 10A. The socket and plug shall be kept dry to
prevent electric leakage. Inspect frequently whether the plugs are well
plugged in the socket. Inspect method is as follows: insert the power
supply plug into the socket,after using for half an hour, shut down the unit
and pull the plug out, and inspect the plug in case it scalds your hand. If
tempeature is over 50, please plug in another socket. to avoid the plug
being damaged, fire or other personnel accidents result from badcontact.
For the places or the wall where the water may splash, the installation
height of the socket shall not be lower than 1.8m.
The wall in which the electric water heater is installed shall be able to bear
the weight equalling twice the weight of the heater fully filled with water
without distortion or cracks. Otherwise, other strengthening measures
The one-way safety valve attached to the machine must be installed to the
cold water inlet of this machine (see Fig.6).
should be adopted.
For the first use (or the first use after maintenance or cleaning), the heater
can not be switched on until it has been (fully) filled with water. When filling
with water, at least one of the outlet valves at the outlet of the heater must
be opened to release the air. This valve can be closed after the heater has
been (fully) filled with water.
During the heating, there may be drops of water dripping from the pressure
release hole of the one-way safety valve. This is a normal phenomenon. If
there is a large amount of water leaking, please contact the professional
maintenance personnel for repair. This pressure release hole shall, under
no circumstances, be blocked; otherwise, the heater may be damaged,
even resulting in safety accidents.
5.
6.
7
From "5"&"6" , customer could know heating status . The light "5" will turn
on when power is connected. The light “6“ will flash when smart control
energy saving mode is started. According the temperature setted, the
light “5" will be shown in red which means water heater is being heated.
When inner water heater temperature reaches the setted value , light “5"
will be shown in white, which means water heater enter into warm-keeping
status.
"4" could show the current inner water temperature as well as setted
temperature value.If no person operates on water heater , the value in
display screen " 4" means current temperature value .By spinning knob
"3" , "4" values will vary accordingly ( i.e temperature setting process) ,
when finish temperature setting , "4" values will return back to actual current
inner water heater temperatrue
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka EWH 50 D SLIM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka EWH 50 D SLIM in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 2.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info