Manual Teka DVN 94030 TTC BK (page 16 of 60) (English, German, French, Polish, Portuguese, Turkish, Spanish)

781142

Zoom out

Zoom in

1/60

• This appliance is marked according to the European directive

2012/19/EC on Waste Electrical and Electronic Equipment

(WEEE).

• By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate

waste handling of this product.

• The symbol on the product, or on the documents

accompanying the product, indicates that this appliance may not

be treated as household waste. Instead it should be taken to the

appropriate collection point for the recycling of electrical and

electronic equipment. Disposal must be carried out in accordance

with local environmental regulations for waste disposal.

• For further detailed information regarding the process, collection

and recycling of this product, please contact the appropriate

department of your local authorities or the local department for

household waste or the shop where you purchased this product.

Appliance designed, tested and manufactured according to:

• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.

• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO

5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO

3741; EN 50564; IEC 62301.

• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;

EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a correct

use in order to reduce the environmental impact: Switch ON the

hood at minimum speed when you start cooking and kept it

running for few minutes after cooking is finished. Increase the

speed only in case of large amount of smoke and vapor and use

boost speed(s) only in extreme situations. Replace the charcoal

filter(s) when necessary to maintain a good odor reduction

efficiency. Clean the grease filter(s) when necessary to maintain a

good grease filter efficiency. Use the maximum diameter of the

ducting system indicated in this manual to optimize efficiency and

minimize noise.

Use

The hood is conceived for the suction of cooking fumes and steam

and is destined only for domestic use.

The hood is designed to be used either for exhausting or filter

version.

Extraction version

In this case the fumes are conveyed outside of the building by

means of a special pipe connected with the connection ring

located on top of the hood.

CAUTION!

The exhausting pipe is not supplied and must be purchased apart.

Diameter of the exhausting pipe must be equal to that of the

connection ring.

CAUTION!

If the hood is supplied with active charcoal filter, then it must be

removed.

Connect the hood and discharge holes on the walls with a

diameter equivalent to the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller

dimensions will cause a diminution of the suction performance and

a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensable length.

! Use a duct with as few elbows as possible (maximum elbow

angle: 90°).

! Avoid drastic changes in the duct cross-section.

Filtration version

The aspirated air will be degreased and deodorised before being

fed back into the room.

In order to use the hood in this version, you have to install a

system of additional filtering based on activated charcoal.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the range

hood must be not less than 45cm from electric cookers and 65cm

from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

As described in the installation drawings perform 6 holes (8 mm

diameter, 40 mm deep), in the positions shown in the drilling

template, to fix the hood support bracket and the exhaust flue.

After installation, check that the hood and exhaust flue are

perfectly aligned.

The range hood is intended to be installed over a hob having

6 heating elements.

Electrical connection

The mains power supply must correspond to the rating indicated

on the plate situated inside the hood. If provided with a plug

connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after installation.

If it not fitted with a plug (direct mains connection) or if the plug is

not located in an accessible area, after installation, apply a double

pole switch in accordance with standards which assures the

complete disconnection of the mains under conditions relating to

over-current category III, in accordance with installation

instructions.

WARNING!

Before re-connecting the hood circuit to the mains supply and

checking the efficient function, always check that the mains cable

is correctly assembled.

Warning! If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified persons in

order to avoid hazard.

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for the

chosen installation area.

• Remove the charcoal (*) filter/s if supplied (see also relative

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Teka DVN 94030 TTC BK in the language / languages: English, German, French, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 6.64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Teka DVN 94030 TTC BK Manual

Product: