Manual Tefal MQ7161 - Multimoulinette (page 22 of 320) (English, Dutch)

724278

Zoom out

Zoom in

1/320

- 22 -

hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

Danger!

The electric power tool generates an electro-

magnetic ﬁ eld during operation. Under certain

circumstances this ﬁ eld may actively or passively

impede medical implants. To reduce the risk of

serious or fatal injuries, we recommend persons

with medical implants to consult their doctor and

the manufacturer of the medical implant prior to

using the equipment.

5. Before starting the equipment

The lawn mower is delivered partly assembled.

The push bar and the grass basket must be as-

sembled before using the lawn mower. Follow the

instructions step by step and refer to the pictures

when assembling.

Mounting the push bar (Fig. 3 to 5)

Start by fastening the lower push bars for the left-

hand side (Fig. 3/Item 10) and the right-hand side

(Fig. 3/Item 11) to the mower housing using the

fastening screws (Fig. 3/Item 12). The upper push

bar then has to be slid onto the lower push bars

and fastened with screws (Fig. 4/Item 13). There

are 2 diﬀ erent holes on each of the lower push

bars for this, to enable the height of the push bar

to be adjusted to the height of the user. Then fas-

ten the power cable to the push bar with the cable

clips (Fig. 5/Item 14).

Mounting the catch basket (see Fig. 6)

Before you ﬁ t the catch basket you must ensure

that the motor is switched oﬀ and the blade is not

rotating. Lift the ejector ﬂ ap (Fig. 6/Item 6) with

one hand. With the other hand, hold the catch

basket by the handle and hook it in from above

(Fig. 6).

Filling level indicator of the grass collector

The grass box is equipped with a ﬁ lling level in-

dicator (Fig. 1/Item 15). which is opened by the

airﬂ ow that the lawn mower generates during ope-

ration. If the ﬂ ap closes during mowing, the grass

collecting device is full and must be emptied. To

ensure the proper functioning of the ﬁ lling level

indicator, the holes under the ﬂ ap must always be

kept clean and passable.

Adjusting the cutting height

Caution!

Adjust the cutting height only when the machine

has been switched oﬀ and the safety plug has

been pulled out.

Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged. To prevent any imbalance, replace

blunt and/or damaged blades. To carry out this

check, ﬁ rst switch oﬀ the motor and pull out the

safety plug.

The cutting height is adjusted as follows (see Fig.

7):

1. Push the lever (5) downwards.

2. Set the lever (5) to the desired cutting height.

3. Release the lever (5) and check that it is se-

curely seated in the lock.

Reading oﬀ the cutting height

The cutting height can be set between 25-65 mm

in 5 intervals, and can be read oﬀ on the scale.

Charging the battery (Fig. 8)

1. Take the battery pack out of the equipment.

Do this by pressing the pushlock button.

2. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Insert the power plug of the charger

(9) into the socket outlet. The green LED will

then begin to ﬂ ash.

3. Insert the battery pack (8) into the battery

charger (9).

4. In the section entitled „Charger indicator“ you

will ﬁ nd a table with an explanation of the LED

indicator on the charger.

The battery pack can become a little warm during

the charging. This is normal.

If the battery pack fails to charge, check:

•

whether there is voltage at the socket outlet

•

whether there is good contact at the charging

contacts

Anl_GAM_E_33_Li_1_SPK7.indb 22Anl_GAM_E_33_Li_1_SPK7.indb 22 30.10.2017 09:44:2030.10.2017 09:44:20

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tefal MQ7161 - Multimoulinette in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tefal MQ7161 - Multimoulinette Manual

Product: