133729
111
Zoom out
Zoom in
Previous page
1/122
Next page
4
111
COOL, HEAT, and FAN ONLY Operation
1. If the AUTO mode is not comfortable, you may manually override the settings by using COOL, DRY,
HEAT (HEAT PUMP units only), or FAN ONLY modes by pressing button
.
2. Push the
or button ( and ) to set the desired room temperature. When in COOLING mode, the
most comfortable settings are 21ºC or above. When in HEATING mode, the most comfortable settings
are 28ºC or below.
3. Push the
Fan button to select the FAN mode of AUTO, HIGH, MED or LOW.
4. Push the
On/off button . The operation lamp lights and the air conditioner starts to operate per your
settings. Push the
On/off button again to stop this unit operation.
DRY Operation
1. Push the Mode button to select DR
Y.
2. Push the
or button ( and ) to set the desired temperature from 21 C to 28 C.
3. Push the
On/off button . The operation lamp lights and the air conditioner starts to operate in the DRY
mode. Push the
On/of
f
button again to stop this unit operation.
TIMER Operation
Push Timer on/off button ( and ) to set the on and off times of the unit. The effective operation time
set by the remote controller for the timer function is limited to a period of between 0.5 and less than 24
hours.
1.
To set the STARTING time
.
1.1
Push the Timer on button , then the remote controller display shows ON TIMER, the last set time for
the starting operation and the signal "
Hr" will be shown on the digital display area. You are now ready
to reset the time to START the operation.
1.2
Push the Timer on button again to set desired unit start time.
1.3
After setting the Timer on ,there will be half a second delay before the remote controller transmits the
signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears
and the set temperature will re-appear on the digital display.
2.
T
o set the STOPPING time.
2.1
Push the Timer of
f
button and the remote controller display will show OFF TIMER and the last set
time for the timer off operation in hours will be shown on the Timer display area. You are now ready
to reset the time of the STOP operation.
2.2
Push the Timer off button again to set the time you want to stop the operation.
2.3
After setting the Timer of
f
, there will be half a second delay before the remote controller transmits
the signal to the air conditioner
. Then, after approximately another 2 seconds, the signal "h" disappe
-
ars and the set temperature will re-appear on the digital display.
NOTE!
Due to the difference of the set temperature of the unit and the actual indoor temperature, the
Air Conditioner when in DRY mode will automatically operate many times without running the
COOL and FAN mode.
N
OTE!
The F
AN ONLY mode cannot be used to control the temperature. In this mode, only steps 1, 3 and
4 are applicable.
man_TS1xx_uk.qxd 10-05-2007 14:12 Pagina 111
111


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tectro ts 126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tectro ts 126 in the language / languages: English, German, Danish, French, Spanish, Finnish as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Tectro ts 126

Tectro ts 126 User Manual - Dutch, Italian, Polish, Turkish, Norwegian - 122 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info