622559
2
Zoom out
Zoom in
Previous page
1/2
Next page
Before finally closing the safe, it is advisable to check that everything is OK by
operating the opening and closing mechanism a number of times with the door open.
Then shut the door and turn the knob anticlockwise until it is closed
OPENING THE SAFE USING YOUR PERSONAL CODE
Press “ON”
Enter your personal code set earlier and press “ENTER”. The green “OK” LED lights up for five
seconds. Within this time, turn the knob clockwise and open the door
SIGNAL INDICATING THAT INTERNAL BATTERY(ES) ARE GOING FLAT
When the internal battery begins to go flat, this is indicated at the end of the opening procedure, by the red
“BATTERY” LED lighting up and a low beep tone. At this point, it will still be possible to open the safe a
number of times. Replace the internal batteries.
EMERGENCY OPENING WITH INTERNAL BATTERY(ES) FLAT
If the failing battery(es) goes completely flat, as soon as the keyboard is pressed, to proceed with opening the
safe, it is necessary to use a new 9-volt LR61 alkaline battery externally (see Pic. 2)
Press the 9-volt battery contacts firmly on the corresponding contacts on the keyboards, ensuring that they
are positioned correctly (the “-“ of the battery touching the bigger contact and the “+” of the battery touching
the small contact). With the battery firmly in position, key in code and open door. Replace internal batteries
immediately.
CAUTION
Wall safes: After installing the safe in the wall, leave the safe open for a few days allow any
dampness to dry out.
Replace alkaline batteries every year.
It must be remembered that even new, packed batteries can sometimes be defective, for various
reasons, or have a brief duration. In the event of failure of the magnet release, or other faults, first of
all, replace the battery with a new alkaline batteries.
The manufacture declines all responsibility for failure to observe the instructions given, or for
improper use of the safe, thus causing the warranty to lapse.
Versions with EMERGENCY KEY
OPENING WITH EMERGENCY KEY
Remove the adhesive label marked with the letter “E” (Pic.3).
Insert the key and open the lock up to the stop point.
Open the door.
Once the door is open, turn the knob anticlockwise until the bolts are fully extended.
Close the lock and remove the key.
WARNING!
NEVER LEAVE YOUR
EMERGENCY KEY IN THE
SAFE
PROGRAMMING
BUTTON
р
iс. 1
BATTERY CASE
REMOVE
р
iс. 3
ADESIVE LABEL
FOR EMERGENCY
KEY
рiс. 2
CONTACT PAD
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technomax SMT tot 2009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technomax SMT tot 2009 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technomax SMT tot 2009

Technomax SMT tot 2009 User Manual - German - 2 pages

Technomax SMT tot 2009 User Manual - Dutch - 2 pages

Technomax SMT tot 2009 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info