Manual Technomate TM-7102 HD (page 4 of 42) (English, French)

486783

Zoom out

Zoom in

1/42

www.technomate.com

Your Digital Partner for Life

This receiver is preinstalled with 25 Satellite and 1500 default Channels and is fully configured.

No settings need to be changed.

After turning ON the receiver, select a language and Country. You will be taken to the

Viewing mode. Press the SAT button on the Remote and select a satellite. To bring up the

Channel List, press the OK button on the remote.

To delete unwanted Satellites-press the MENU button on the remote and go to Installation.

Press OK and OK on Satellite Setup. Press OK again and a Satellite List will appear. To delete a

Satellite, press the BLUE( ) button on the remote.

This receiver is preinstalled with 25 Satellite and 1500 default Channels, and is fully

configured.No settings need to be changed.

Press the MENU button on the remote.Press OK on Installation. Go to Motorised Setting and

press OK. Go to the Third line (DiSEqC Motor) and use the Left/Right arrow buttons on the

remote to select USALS. Then go to Position Setting and press OK. Then go to Longitude and

Latitude and enter the coordinates of where you live (London’s Longitude is 000. 1 West;

South of UK’s Latitude is 51.5 North).Press the EXIT button on the remote. Go to GOTO and

press OK. Wait until the Signal Quality is more than 40% in the progress bar. When a Satellite is

found, then all the selected 25 Satellites are fully configured for a Motorised system.

If the Signal Quality is below 40%, then the settings are incorrect and the Longitude needs to

be adjusted, for example: 000.2, 000.3, 000.4,5/6/7/8/9 West or East. The Latitude may also

need to be adjusted. If you still have not got a signal, then the external installation (dish, etc)

needs to be adjusted.

Press the MENU button on the remote and go to Installation and press OK. Go to Motorised

Setting and press OK. Press OK again to open the satellite list. Select a satellite from the list

and press OK. Go to the Third line (DiSEqC Motor) and use the Left/Right buttons on the

remote to select DiSEqC 1.2. Go to Move and press and hold the Left/Right buttons on the

remote until you get a Signal Quality of more than 40%. Go to Save and press OK. Press the

RED( )button on the remote to Scan. To scan extra satellites, repeat the above.

How to Motorise 25 Satellite & 1500 Channels with USALS in 60secs

How to Setup a DiSEqC 1.2 Motorised System

If you want to start the receiver without the preinstalled Satellites and Channels, press the

MENU button on the remote and go to System Settings and press the OK button. Go to

Factory Reset, press OK and enter 0000. Then select Factory Reset. Press OK and select Yes.

How to do a Factory Reset to Delete the Preinstalled Satellites and Channels

Press the MENU button on the remote and press the OK button on Installation. Press OK on

Satellite Setup and OK again to display a Satellite List. To add a Satellite, press the YELLOW

( )button on the remote. Press the EXIT button on the remote to exit the list.

When the Quality Bar is at its highest level, press the RED( ) button on the remote to Scan

the Satellite. To view a channel, press the OK button in

the Viewing Mode (clear screen) and select any channel. To view $ (Scrambled) channels, a

CAM (Decoder) and a viewing card are required.

Press the MENU button on the remote and press the OK button on Installation. Press OK on

Satellite Setup and OK again to display a Satellite List. Select a Satellite (e.g. Hotbird 13E and

Astra 19.2E) and press the YELLOW button on the remote for each Satellite to Save. Press the

EXIT button on the remote to exit the list.

Go to DiSEqC Switching and select a Satellite (e.g. Hotbird 13E as Number 1 and Astra 19.2E as

Number 2). When the Quality Bar is at its highest level for each Satellite, press the RED ()

button on the remote to Scan. To view a channel, press the OK button in the Viewing

Mode (clear screen) and select any channel. To view $ (Scrambled) channels, a CAM

(Decoder) and a viewing card are required.

If the above installation was not successful, change the DiSEqC Switching number, e.g. Hotbird

13E as Number 2 and Astra 19E as Number 1.

How to Install a New Satellite (Fixed Non-Motorised System)

How to Setup a Monoblock or DiSEqC Switch (up to 4 LNBs / Dishes)

Press the MENU button on the remote and press the OK button on Installation. Press OK on

Satellite Setup and OK again to display a Satellite List. Select a Satellite (e.g. Hotbird 13E and

Astra 19.2E) and press the YELLOW button on the remote for each Satellite to Save.

Press the EXIT button on the remote to exit the list.

Press the EXIT button again. Press OK on Motorised Setting. Press OK again to display a Satellite

List. Select a Satellite and press OK. Go to the Third line (DiSEqC Motor) and use the Left/Right

buttons on the remote to select DiSEqC 1.2. Go to Move and press and hold the Left/Right

buttons on the remote until you get a Signal Quality of more than 40%. Go to Save and press

OK. Press the RED button on the remote to Scan. Repeat the above for more satellites.

How to Setup DiSEqC 1.2 Motorised System

Press the MENU button on the remote and press the OK button on Installation. Press OK on

Satellite Setup and OK again to display a Satellite List. Select a Satellite (e.g. Hotbird 13E and

Astra 19.2E) and press the YELLOW ( ) button on the remote for each Satellite to Save.

Press the EXIT button on the remote to exit the list.

Press the EXIT button again. Go to Motorised Setting and press OK. Go to the Third line (DiSEqC

Motor) and use the Left/Right arrow buttons on the remote to select USALS. Then go to Position

Setting and press OK. Then go to Longitude and Latitude and enter the coordinates of where

you live (London’s Longitude is 000.1 West; South of UK’s Latitude is 51.5 North). Press the EXIT

button on the remote. Go to GOTO and press OK. Wait until the Signal Quality is more than 40%

in the progress bar. Press the RED ( ) button on the remote to Scan.

How to Setup a USALS Motorised System

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Technomate TM-7102 HD in the language / languages: English, French as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Technomate TM-7102 HD Manual

Product: