541948
5
Zoom out
Zoom in
Previous page
1/7
Next page
Batteries installation
1. Open battery compartment on the back of the unit by removing the two small
screws (RTS 2) with a Philips head screwdriver. (see figure 4)
2. Install / replace with 2x “AAA size batteries in the compartment. It is
recommended that only alkaline batteries are used. Do not use rechargeable
batteries.
3. The weather station is capable of receiving up to 3 different channels. Select
the channel number (1, 2, or 3) by sliding the “Channel 1 2 3” switch (RTS 4).
If you only have 1 remote temperature sensor, select 1.
4. Press the “reset” button (RTS 3) once and the red light will flash once.
5. Replace the battery compartment on the back of the unit by tightening the
two screws (RTS 2).
Installation
1. Place the remote temperature sensor at a desired place by mounting the
units hang hole (RTS 1) on a screw (screw not included). Alternatively, the
unit can be place on a flat horizontal surface.
2. The unit can be placed indoor or outdoor. The unit is weather proof. Do not
submerge unit in water. Do not expose unit to water for prolonged periods.
Avoid accumulation of water and or snow on unit. Avoid exposing unit to
direct sunlight. Remove unit from the exterior in extreme or harsh weather,
including but not limited to hurricane, typhoon, and cyclones seasons. Do not
place the unit in area of high winds.
3. Do not place the remote temperature sensor more than 30 meters (98 feet)
from the receiving weather station. The remote temperature sensor is most
effective if there are no obstruction and interference between the remote
temperature sensor and the weather station. The remote temperature sensor
might have to closer than 30 meters if the weather station is not able to
receive any signals. This is due to obstructions and interference. The user
might need to experiment with various locations to get the best reception.
Configuring Weather Station to receive remote temperature signals.
1. Follow the above instructions to set up remote temperature sensor.
2. Press “CHANNELbutton (6) on weather station for 3 seconds. will flash.
This will reset all temperature memories.
3. The weather station will begin scanning for signals for channel 1. As soon as
signals are received for channel 1, the temperature will be displayed. The
weather station will automatically scans for the other channels. It will scan
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Techno line WT643 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Techno line WT643 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Techno line WT643

Techno line WT643 User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info