542194
47
Zoom out
Zoom in
Previous page
1/54
Next page
64
7. Dès l’af chage de toutes les données externes et du symbole « Channel 2 » sur l’écran de la
station météo, mettre les piles dans le troisième émetteur. Les données du troisième émetteur
externe devraient af cher « Channel 3 » en 2 minutes maximum. Si les données du troisième
émetteur externe sont bien reçues, le symbole « Channel 1 » s’allume. Si rien n’apparaît, vous
devez recommencer à zéro.
Les piles doivent être mises en place dans le troisième émetteur externe 10
secondes maximum après réception des données du deuxième émetteur externe.
8. Pour que la réception du signal de 868 MHz soit suf sante, la distance entre le lieu d’installation
de la station météo et l’émetteur externe ne doit pas dépasser 100 mètres.
Les instructions de positionnement des émetteurs externes supplémentaires
doivent être suivies correctement pour éviter tout problème de transmission. Si
des problèmes surviennent, vous devez retirer les piles de tous les appareils et
recommencer à zéro.
Si les piles sont épuisées, un symbole désignant leur statut s’af che. Ce symbole apparaît en haut
et à droite de l’écran dans la zone «Indoor » pour montrer que les piles de la station météo doivent
être changées. Le symbole situé en bas et à droite de l’écran dans la zone «Outdoor » désigne le
statut des piles de l’émetteur externe.
49
Once the weather tendency indicator has registered a change in air pressure, it will
remain permanently visualized on the LCD.
N) Display of indoor temperature and humidity reading
The indoor temperature and humidity are measured automatically and displayed on the fourth
section of the LCD.
O) Display of outdoor temperature
The last LCD section shows the outdoor temperature, a reception symbol and a channel number under
the temperature will also show if more than one transmitter has been used.
P) Display of indoor maximum and minimum records
1. In normal display mode, press the “MIN/ MAX” button (2) three times. The maximum indoor
temperature and humidity will be shown. Also the date and time of recording this temperature
will be displayed.
2. Press the “MIN/ MAX” button (2) once more to display the minimum indoor temperature and
humidity. Also the date and time of recording this temperature will be displayed.
Q) Resetting the indoor maximum/ minimum records
1. In normal display mode, press the “MIN/ MAX” button (2) to advance to the MIN/ MAX display.
2. Press and hold the “SET” button (1) for about 3 seconds, this will reset all indoor minimum and
maximum data recorded to the current time, date, temperature and humidity.
The max/ min temperature of the currently selected outdoor channel will also be
reset at the same time.
R) Display of outdoor maximum and minimum records
1. In normal display mode, press the “CH/ +” button (3) to select the desired channel. The channel
ID will be displayed above the outdoor temperature reading.
2. Press the “MIN/ MAX” button (2), the max temperature of the selected channel will be
displayed. Also the date and time of recording this temperature will be displayed.
3. Press the “MIN/ MAX” button (2) once more, the min temperature of the selected channel will
be shown. Press the “ALM” button (4) to go back to the normal display mode.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Techno line WS 9611 IT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Techno line WS 9611 IT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Techno line WS 9611 IT

Techno line WS 9611 IT User Manual - English - 39 pages

Techno line WS 9611 IT User Manual - German - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info