•When you insert the batteries all the symbols on the display will briefly light up and you will hear a signal tone, LCD full display for 2 seconds with
beeping, then enter RCC reception for seven minutes.
•If this automatic setting process is unsuccessful, then use a sharply pointed instrument to press the Reset button on the rear side of the clock.
Manual time setting:
•Press and hold down the “SET” button for 2 seconds, the 12/24 hour mode display starts to flash. Now use “▲” and “▼ “buttons to set the
correct 12/24 hour mode.
•Press “SET” to confirm your setting, the offset display starts to flash. Now use “▲” and “▼“buttons to set the correct time zone.
•Press “SET” to confirm your setting, the Hour display starts to flash. Now use “▲” and “▼“buttons to set the correct hour.
•Press “SET” to confirm your setting, the Minute displays starts to flash. Now use “▲” and “▼“buttons to set the correct minute.
•Press “SET” to confirm your setting, the Year display 2004 starts to flash. Now use “▲” and “▼” buttons to set the correct year.
•Press SET to confirm your setting, the Month display starts to flash. Now use “▲” and “▼” buttons to set the correct month.
•Press “SET” to confirm your setting, the Date display starts to flash. Now use “▲” and “▼“ buttons to set the correct date.
•Press “SET” to confirm your setting, the language selection for the Weekday displays starts to flash. Now use “▲”and “▼“ buttons to select a
language.
•Press “SET” to confirm your setting and to end the setting procedures, enter the clock mode.
nfo:
•After 30 seconds without pressing any button, the clock switches automatically from set mode to normal time mode.
Setting the daily alarms:
To view the set alarm times, under the clock mode, press once ALARM button, LCD displays the “” icon.
•Press and hold down the ALARM button for 2 seconds until Alarm Time flashing icon is displayed. Now use the “▲” and“▼“ buttons to select
the alarm time you require and briefly press the ALARM button to set this Alarm time.
•The Hour display of the Alarm time starts to flash. Use the “▲” and “▼“buttons to set the required hour. Press ALARM button to confirm your setting
•The Minute display of the Alarm time starts to flash. Use the “▲” and “▼“buttons to set the required minute. Press ALARM button to confirm
your setting and to end the setting procedure.
•To activate or deactivate the daily alarms, briefly press the “ALARM” button once.
Info:
•After 30 seconds without pressing any button the clock switches automatically from setting mode to Normal clock mode.
•The alarm will sound for 2 minutes if you do not deactivate itby pressing any button. In this case the alarm will be repeated automatically after
24 hours.
•Rising alarm sound changes the frequency 4 times while the alarm signal is heard.
Automatic Snooze function:
•Proceed as follows to activate the automatic Snooze function: While the alarm is sounding, press the SNOOZE button to activate snooze function.
display.
•This operation moves the alarm back by 5 minutes and the alarm will restart at this time.
•The Snooze function can be interrupted by pressing any button.
deviations to the exact time. If this synchronization attempt is unsuccessful (the radio mast icon disappears from the display), the system will
automatically attempt another synchronization at the next full one hour. This procedure is repeated automatically up to total 5 times.
•To start manual DCF signal reception, press the “WAVE“ button. If no signals received within 7 minutes, then the DCF signal search stops (the
radio mast icon disappears) and start again at the next full one hour.
•During RC reception to stop searching radio signal, press the “WAVE“ button once.
Info:
•A flashing radio mast icon indicates that the DCF signal reception has started
•A continuously displayed radio mast icon indicates that the DCF signal was received successfully
•We recommend a minimum distance of 2.5 meters to all sources of interference, such as televisions or computer mo- nitors
•Radio reception is weaker in rooms with concrete walls (e.g.: in cellars) and in offices. In such extreme circumstances, place the system close to
the window.
Hereby, Technotrade declares that this product WS8005 is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU and ROHS 2011/65/EC. The original EU declaration of conformity may be found at: www.technoline.de/doc/4029665080055
Environmental reception effects
The clock obtains the accurate time with wireless technology. Same as all wireless devices, the reception is maybe affected by the following
circumstances:
•long transmitting distance
•nearby mountains and valleys
•near freeway, railway, airports, high voltage cable etc.
•near construction site
•among tall buildings
•inside concrete buildings
•near electrical appliances (computers, TV’s, etc) and metallic structures
•inside moving vehicles
Place the clock at a location with optimal signal, i.e. close to a window and away from metal surfaces or electrical appliances.
Precautions
•This main unit is intended to be used only indoors.
•Do not subject the unit to excessive force or shock.
•Do not expose the unit to extreme temperatures, direct sunlight, dust or humidity.
•Do not immerse in water.
•Avoid contact with any corrosive materials.
•Do not dispose this unit in a fire as it may explode.
•Do not open the inner back case or tamper with any components of this unit.
Batteries safety warnings
•Use only alkaline batteries, not rechargeable batteries.
•Install batteries correctly by matching the polarities (+/-).
•Always replace a complete set of batteries.
•Never mix used and new batteries.
•Remove exhausted batteries immediately.
•Remove batteries when not in use.
•Do not recharge and do not dispose of batteries in fire as the batteries may explode.
•Ensure batteries are stored away from metal objects as contact may cause a short circuit.
•Avoid exposing batteries to extreme temperature or humidity or direct sunlight.
•Keep all batteries out of reach from children. They are a choking hazard.
Use the product only for its intended purpose!
Consideration of duty according to the battery law
Old batteries do not belong to domestic waste because they could cause damages of health and environment. You can return used batteries
free of charge to your dealer and collection points. As end-user you are committed by law to bring back needed batteries to distributors and
other collecting points!
Consideration of duty according to the law of electrical devices
This symbol means that you must dispose of electrical devices separated from the General household waste when it reaches the end of its
useful life. Take your unit to your local waste collection point or recycling centre. This applies to all countries of the European Union, and to
other European countries with a separate waste collection system.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Techno line WS 8005 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Techno line WS 8005 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 0.36 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
