Manual Techno line TM 3055 (page 2 of 2) (English)

542290

Zoom out

Zoom in

1/2

4. Conﬁguration menu

The conﬁguration menu can be used to modify settings.

To access this menu, press and hold down the menu

button (for more than 3 seconds).

PRO: For setting the weekly program (see Section “1 •

Setting the weekly program”)

DAT: For modifying the time of day and date•

POS: For querying the actuator’s current position•

DST: Automatic switchover at the start or end of daylight •

saving time can be deactivated.

AER: For setting the “window open” temperature and •

time so that the temperature is automatically reduced

in the event of ventilation

TOF: For setting the offset temperature•

RES: For restoring the factory settings•

Use the setting wheel to select menu items and the OK but-

ton to conﬁrm your choice. Press the menu button again to

return to the previous level. After 65 seconds without any-

thing happening, the menu will close automatically.

5. Display content during normal operation

During normal operation,

the following are displayed:

switching periods, operating

mode, temperature setting

and day of the week.

The bars indicating the weekly program’s switching peri-

ods are shown for every othe r time interval. For an examp-

le, please refer to “2. Weekly program: Examples”.

6. Setting the holiday function

If you want a ﬁxed temperature to be maintained for a set

period of time while you are on holiday or during a party,

you can make use of the Holiday function.

Press and release the menu button repeatedly until the •

suitcase symbol (

) appears on the display.

Use the setting wheel to set the end of the time period •

during which the temperature is to be maintained.

Press the OK button to conﬁrm.•

Then use the setting wheel to set the date.•

Press the OK button to conﬁrm.•

Use the setting wheel to set the temperature; press OK to •

conﬁrm. The display will ﬂash to conﬁrm your settings.

The set temperature will remain in force until the speciﬁed

time. After that, the actuator will adopt Auto mode.

7. Comfort and set-back temperatures

The comfort/set-back temperature button (

) provides

an easy and convenient way of switching between these

two temperatures. The factory settings are 21.0°C and

17.0°C respectively. To adapt them, proceed as follows:

Press and hold down the comfort/set-back temperature •

button (

) for more than 3 seconds.

The sun symbol ( •

) will appear on the display along

with the current comfort temperature.

Use the setting wheel to modify the temperature; press •

OK to conﬁrm.

The moon symbol ( •

) will appear together with the set-

back temperature.

Use the setting wheel to modify the temperature; press •

OK to conﬁrm.

The temperature can even be modiﬁed in Auto mode at any

time by using this button. The new setting will be retained

until the program’s next switching time.

8. Child-proof lock/Operating inhibit

Operation can be inhibited.

To activate/deactivate the operating inhibit, brieﬂy press •

the Menu and

buttons at the same time.

Once the function is active, “LOC” will appear on the display.•

To deactivate the function, press both buttons again.•

9. Setting the heating break

If the heating is being switched off for the summer, you can

save battery power. This involves opening the valve up fully.

Limescale protection measures remain in place.

To activate the heating break, turn the setting wheel •

clockwise during manual operation (Manu) until “ON”

appears on the display.

To terminate the heating break, quit manual operation •

(Manu) or turn the setting wheel anticlockwise.

10. Setting frost protection mode

If you do not want the room to be heated, the valve can

be closed. It will only be opened again if there is a risk of

freezing due to frost. Limescale protection measures re-

main in place.

To activate frost protection mode, turn the setting wheel •

anticlockwise during manual operation (Manu) until “OFF”

appears on the display.

To terminate frost protection mode, quit manual opera-•

tion (Manu) or turn the setting wheel clockwise.

11. “Window open” function

In the event of a signiﬁcant drop in temperature, the actu-

ator can automatically detect whether the room is being

ventilated. To save on heating costs, the temperature is

then automatically reduce d for a speciﬁc time pe riod (fac -

tory setting: 15 minutes). While this function is active, the

“window open” symbol (

) appears on the display.

Press and hold down the menu button for more than •

3 seconds.

Use the setting wheel to select the “AER” menu item.•

Conﬁrm with OK.•

Use the setting wheel to set the temperature and time. •

To deactivate the function, select a time of “0”.

12. Setting the offset temperature

The temperature is measured at the heating appliance

itself, with the result that other parts of the room may be

warmer or colder than this. To allow for this, you can set

a temperature offset of ±3.5°C. If, for example, a tempe-

rature of 18°C is measured somewhere within the room

instead of the 20°C set, it means that an offset of -2.0°C

needs to be conﬁgured.

Press and hold down the menu button for more than •

3 seconds.

Use the setting wheel to select the “TOF” menu item.•

Conﬁrm with OK.•

Use the setting wheel to modify the temperature.•

Press the OK button to conﬁrm.•

13. Restoring the factory settings

You can reset the actuator to its initial state manually. This

will clear all the settings that have been made manually.

Press and hold down the menu button for more than •

3 seconds.

Use the setting wheel to select the “RES” menu item.•

Conﬁrm with OK.•

“CFM” will appear on the display; press OK to conﬁrm.•

14. Intended use

The energy-saving controller has been designed for the

purpose of controlling a standard heating appliance val-

ve. The device may only be operated indoors and must

be protected from the effects of damp and dust, as well

as solar radiation and sources of radiant heat.

Using the device for a purpose or in a manner other than

that described in this operating manual constitutes a

breach of the “intended use” and shall invalidate the war-

ranty and any liability claims. The same shall apply in the

event of any conversion or modiﬁcation work. The devices

are intended exclusively for domestic use.

15. Troubleshooting and maintenance

Error code on

display

Problem Remedy

Battery symbol

(

)

Battery power

too low

Replace batteries

Valve actuator

sluggish

Check installation,

inspect heating

valve

Adjusting range

too large

Check

actuator

fastening

Adjusting range

too small

Check heating

valve

At 12:00 every Saturday, the actuator performs a

weekly descaling function to prevent valve calciﬁca-

tion. “CAL” will appear on the display.

16. Instructions for disposal

Do not dispose of the device with regular domestic

waste.

Electronic equipment must be disposed of at local

collection points for waste electronic equipment in

compliance with local directives governing waste

electrical and electronic equipment.

The CE sign is a free trade sign addressed ex-

clusively to the authorities and does not warrant

any properties.

17. Safety instructions

The devices concerned are not intended for children and

must not be used as toys. Do not leave packaging materi-

al lying around, as children might be tempted to play with

it, which is extremely dangerous. Do not open the device:

it does not contain any components that need to be ser-

viced by the user. In the event of an error, please return

the device to our service department.

Issue 1 English 11/2009

CC-RT-O-CyI-W-R3, V1.0 914-01

19. Technical properties

Supply voltage: 3 V

Max. current consumption:

100 mA

Batteries: 2x LR6 batteries (Mignon/AA)

Battery life: Approx. 3 years

Display: LC display

Housing dimensions: 63 x 72 x 102 mm (W x H x D)

Ambient temperature: +5 to +55°C

Max. surface temperature: +90°C (of radiator)

Linear travel: 4.2 mm

Spring force: max. 80 N

Connection: M30 x 1.5

We reserve the right to make any technical changes

that constitute an improvement to the device.

18. Adapter overview

Manufacturer Figure Adapter

Heimeier, MNG, Jun-

kers, Landis&Gyr

“Duodyr”, Honeywell-

Braukmann, Oventrop,

Schlösser, Simplex,

Valf Sanayii, Mertik

Maxitrol, Watts,

Wingenroth (Wiroﬂex),

R.B.M., Tiemme, Jaga

No adapter

required

Danfoss RA

Included

in scope of

supply

Danfoss RAV

Included

in scope of

supply

Danfoss RAVL

Included

in scope of

supply

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Techno line TM 3055 in the language / languages: English as an attachment in your email.

The manual is 1,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Techno line TM 3055

Techno line TM 3055 User Manual - German - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Techno line TM 3055 Manual

Product: