613204
14
Zoom out
Zoom in
Previous page
1/364
Next page
14
Switching the equipment on/o
6 Operation
6.1 Turning the TV set on and off
6.1.1 Turning on with the mains switch on the TV set
> Switch the TV set on by pressing the mains switch.
The TV set now runs through an initialisation procedure and cannot be operated
during this period. This procedure can take the few seconds.
6.1.2 Turning on from the standby mode
> Switched the TV set on by pressing the On/Standby key or the Programme +/- keys
on the remote control /on the TV
1)
or by pressing one of the numeric keys from 0 to 9
on the remote control. The green LED display signals the operating condition.
6.1.3 Switching to the standby mode
> Turn the TV set o by pressing the On/Standby key on the remote control/on the set
1)
.
Please note that when the set is switched o it also checks whether a new operating software
2)
or programme list
3)
is available. This procedure can take some time. The LED shines orange
and the LCD panel is already switched o during the test.
The television set is turned on again immediately, if the On/Standby key is pressed during the test.
The television set switches to standby after the test has been carried out, the LED now shines red.
The TV set is now in the standby mode and can be completely switched o with the mains switch.
If new operating software
2)
or a new programme list
3)
was found during the test,
this is displayed when the TV set is switched on the next time.
The new software or programme list can then be downloaded immediately.
6.1.4 Turning off with the mains switch on the TV set
> The TV set is completely turned o by pressing the mains switch.
Please note that in this case neither software nor “SFI+” data
can be downloaded and the timer can also not be used.
Please note that the TV set may only be turned o with the mains switch when it is in the
standby mode. This prevents the loss of data and possible damage to the les or hard disk.
The device remembers, whether it was set to “On” or “O”,
as entered with the remote control or keys of the set
1)
.
In the case of an electrical power outage, the TV set should therefore be switched o
during ongoing operation with the mains switch to prevent it turning itself on
inadvertently as soon as power is available again.
1) Only possible with the remote control for HDTV 32 Plus and HDTV 40 Plus.
2) Only from DVB-S (ASTRA 19.2° East) and DVB-C/DVB-T (when data channel is available).
3) Only from DVB-S (ASTRA 19.2° East).
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technisat HDTV 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technisat HDTV 40 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info