Manual Technisat DigiPal 2 TX e DVB-T (page 3 of 56) (English, French, Italian, Spanish)

486807

Zoom out

Zoom in

1/56

DigiPal 2 TX e

Your unit carries the CE logo, and complies with all relevant EU standards.

Subject to change without notice, subject to printing errors.www.technisat.com

Quick Start Guide DVB-T

ENCZFRESIT

You

r unit carries the CE logo, and complies with all relevant EU standards.

Sub

jec

t t

o c

han

wit

hou

t n

oti

ce,

bje

pri

nti

errors.www.technisat.com

Menue

Disposal Information

The unit‘s packing materials are made exclusively of recyclable materials. Please dispose of them >

according to the “Dual System.” Please note that the empty batteries from the remote control as well as

electronic waste are not disposed of in the normal waste receptacle, but in the proper place.

* if available

Safety Information

For your safety, you should carefully read through the safety notes before you use this unit.

The manufacturer does not take responsibility for any damages that result from improper use and/or

disregard for the prescribed safety measures.

In order to insure proper ventilation, place the unit on a smooth, flat surface and do not put anything on >

the lid of the unit. Ventilation slits are here, through which heat is funneled out from the interior of the

device.

Do not put anything lit on the unit, i.e. candles. >

Do not spray or allow water to drip on the unit and do not place anything filled with water on the unit, i.e. >

vases.

Breaks in operation

The unit should be unplugged in case of storm or longer periods of absence (i.e. vacation.)

DVB-Receiver to cable connection

a. DVB-Receiver connection to the

antenna plug of the DVB-T

antenna connection.

b. DVB-Receiver Scart connection

to the television unit.

c. Video unit Scart connection to

the VCR Scart plug on the

DVB-Receiver.

d. Cable output connection to the

television antenna input.

e. Cable output connection

with hi-fi unit.

f. Power connection.

Card reader for smart cards*:

> Insert the smart card (gold chip facing

down, towards the slot) until it stops,

into the card reader.

Inserting the CI-Module**:

> Please take the CI-Module and card manufacturer‘s

instructions into account.

> Insert the desired smart card into the respective CI-Module.

> Insert the CI-Module carefully into the slot.

Important operating instructions

Through the use of the so-called “On Screen Display” (screen projection,) the use of the Digital-Receiver is

made easy and the number of remote control keys is reduced. All functions are shown on the screen and can

be manipulated with just a few keys.

* Depending on model

** if available

Sound On/Off

Numeric keys

Option

Sound/Subtitle selection,

special functions

Arrow key up

Programme +

Arrow key left

Volume -

Arrow Key Down

Programme -

EPG

Programme +/-

Sleep timer

Video text*

On/Mix/Off

On/Stand-by

Multi-function keys

Programme list On/Off

Arrow key right

Volume +

Back

Info

TV/Radio

Volume +/-

Menu On/Off

EXTERNAL

Stop/Freeze-frame

*Remote control options:

It is possible to operate two receivers, one TV

set as well as video recorder with the same

encoding with this remote control by switching

the remote control option.

> To change the remote control option

press the required (SAT1, SAT2, VCR or

TV) key and OK simultaneously!!! Please

note: To control this receiver, you have to

select mode Sat 1.

Illustrations - Remote control

Functions that belong together are grouped in menus. The chosen function is highlighted in color.

On the bottommost line, the “function keys” are highlighted with red, yellow, green and blue bars.

These bars have different functions in each menu that are called up by pressing the respective

colored key (multi-function key) on the remote control. The “function keys” are only active when

the shortcut symbol is shown in the particular field.

Help

If included, a help text can be faded in or out by pressing the blue function key in the menu.

Initial Installation

When operating the unit for the first time, the start window of the installation assistant Auto Install

appears. Please follow the instructions on the screen.

If the initial installation is not run or canceled, the unit will be started with the standard

configuration.

For daily use

Switching on and off

Turn on the Digital-Receiver by pressing the On/Standby button on the remote control or on the unit >

itself.

By pressing the button again, the unit is turned off. >

Choosing programmes

Using the up/down keys:

Switch programmes, one at a time, using the up/down programme keys on the remote control or on the >

unit.

Using the number pad:

Us ing the number pad input the programme number. For example: >

1 for programme 1

1, then 4 for programme 14

2, then 3, then 4 for programme 234.

When inputting programme numbers, you have about 3 seconds after pressing a key to complete

the number. If you have a single or double-digit number to input, you can speed up the process by

holding the last key pressed.

Using the programme list:

Press the “OK” key. >

Now you can choose the programme you wish by using the up and down arrow keys. >

By pressing the “OK” key, the highlighted programme is selected. >

With the up and down arrow keys, you move the highlighted area up or down one line. >

With the left and right arrow keys, you change list pages. >

Returning to the last selected programme:

By pressing the “back” key on the remote control, the last selected programme is re-selected. >

Press the key again and the last programme seen is selected. >

After each programme change, an Info box appears with the programme number and name of

the selected programme, like with Video Text, 16/9 shows or for encrypted content. If a TV show

is available in multiple languages or lines, or in the case of radio programmes, more than one

programme is available under a single programme spot; this information will also be blended in.

In this case, you can choose a language or line using the following method:

Press the “ > Option” key. A list of the current languages available will appear on the screen.

Select the language and or radio programme with the > up and down arrow keys and confirm with “OK.”

Now you can hear the programme in the chosen language. The reception of mono programmes is

also possible with your digital receiver.

With the > right and left arrow keys, you can switch between mono line 1(), mono line 2(), and stereo

Volume control

Adjust the volume of your digital receiver by using the volume + (louder) and volume - (softer) keys. >

By pressing the mute key, sound is switched on or off. >

TV/Radio selection

By pressing the TV/Radio key, you switch between TV and radio modes. >

Sorting programmes/Configuring favorites lists

This chapter describes how you can change the factory settings of your Digital Receiver and

programme favourites lists to fit your needs. This function is also needed to add a newly found

programme to your list.

Keep the following in mind: Your unit has two programme lists, a favorites list and a whole

list. The favorites programme list has all programmes that you have selected using the method

explained below. In the whole list, all programmes are listed.

Programme list management

In order to edit your favorites list, use the following method:

Call up the main menu using the menu key. >

Select the line “TV lists” with the up and down arrow keys, in order to edit the TV lists, or “Radio >

lists,” in order to edit the radio lists respectively.

Confirm with “OK.” The programme management list tool appears for editing the particular favorites >

list (TV or radio list.) On the right side of the screen, the favorites list is shown. On the left side of the

screen, you see the whole list, sorted alphabetically. All available programmes are shown in this

whole list.

By pressing the red function key, the selection is changed to the whole list. This is now active. >

By pressing the key again, a selection window is blended in. Here, you can sort the whole list >

according to different criteria (e.g. all stations, all free stations, all new stations, all found stations, all

English stations etc.) or even provider.

Choose the programme list using the up and down arrow keys (e.g. whole list.) >

Confirm with “OK.” Now a further selection window appears. >

Select the selection criteria using the up and down arrow keys, according to which the whole list >

should be sorted. Choose, for example “all stations,” in order to show all programmes that are in the

whole list or “all new,” in order to show all newly found programmes (from the last ran “find” com-

mand) or “all English,” in order to show all English programmes.

Confirm with “OK.” >

Now, according to your selection, a programme list with “all,” “all new,” or “all English language”

programmes, will be displayed. Programmes that have already been added to the favorites list are

marked with a check.By pressing the red function key “Programme” or the green function key “TV

list,” you can toggle between the favorites list and the whole list. The active list is marked blue.

Adding programmes to the favorites list

In order to put programmes from the whole list into the favorites list, start the programme list

management, as described before, and switch to the whole list.

Press the blue function key, “Functions.” A selection window appears with the available functions. >

Select the lines to add with the up and down arrow keys. >

Confirm with “OK.” >

Select the programme that you want to add to the list with the up and down arrow keys. >

By pressing the yellow function key, “Add,” the selected programme will be added to the favorites list. >

Block selection

In order to select multiple programmes at once, use the following method:

By pressing the “OK” key, the selection mode is started. The selected programme is marked with

an “x” on the left side.

Using the up and down arrow keys, the following or previous programmes can also be selected. >

After you have selected the programmes in this way, press the yellow function key “Add,” in order to >

add the selected programmes to the favorites list.

Removing programmes

In order to remove programmes from the favorites list, start the programme list management. You

are now in the favorites list.

Press the blue function key, “Functions.” >

A selection window with the available functions appears.

Select the line “Remove” with the up and down arrow keys. >

Confirm with “OK.” >

Select the programme that you want to remove from the list with the up and down arrow keys. >

Press the yellow function key, “Remove.” The message “Remove programme(s) from the list?” appears. >

Select yes or no with the right and left arrow keys. >

Confirm your selection with “OK.” >

In this way, removed programmes are still in the whole list and can always be added back to the

favorites list.

Erasure from the whole list

In order to remove programmes from the whole list, use the method described above. Switch

to the whole list after starting the programme list management by pressing the red function key,

“Programmes,” and then choose the function “Remove.”

Sort programmes

In order to change the order of the programmes in your favorites list according to your wishes,

start the programme list management. You are now in the favorites list.

Press the blue function key, “Functions.” A window with available functions appears: >

>Select “Sort Line” with the up and down arrow keys. >

Confirm with “OK.” >

Select the programme that you want in another position in the list with the up and down arrow keys. >

Press the yellow function key, “Sort.” A double arrow appears next to the selected programme. >

Now you can move the selected programme with the help of the up and down arrow keys and/or >

number pad to the place in the list where you want the programme to be.

By pressing the yellow function key, “Sort,” the programme is saved in the new position. >

Ending the menu

By pressing the TV/Radio key, you are returning to normal operation mode.

Start electronic programme magazine

Press the SFI/EPG key on the remote control of the digital receiver. >

The electronic programme magazine appears on the screen. Here, the programmes that you have

selected or the factory settings, with the current content, are shown. Now you can inform yourself about

the content of different programmes through the EPG function. EPG functions are also available, for

example, choosing a particular programme, setting a particular programme, or setting the recording timer.

Ending EPG

By pressing the menu or TV/Radio respectively, you can return to normal operation. >

Recording with the timer

Your receiver has a video recorder and station change timer, respectively. As to programming these

timers, they only differ according to timer type. You can set the timer manually, as described in this

chapter, or with the EPG function.

Programming the timer manually

Start the main menu with the menu key. >

Select the line, “Manage Timer,” using the up and down arrow keys. >

Confirm with “OK.” The sub menu, “Manage timer,” appears. >

Choose the timer type you want to set with the up and down arrow keys. >

By pressing the “OK” key, you arrive at the command window for the programming of a new timer event. >

To set this, use the following method:

Source

Select the column, “Source,” with the arrow keys. >

Press the “OK” key. >

Choose the source (TV or radio) in the open selection window with the up and down arrow keys. >

Confirm with “OK.” Now, according to your previous settings, the TV or radio lists are shown. >

Select the programme with the arrow keys. >

With the up and down arrow keys, you move up or down one line in the list. >

With the left and right arrow keys, you toggle between pages. >

By pressing the “OK” key, your selection is set in the timer. >

Date

Select the “Date” column with arrow keys. >

Enter the four-number date with the number pad, when the timer event should take place. >

Start

Select the “Start” column with the arrow keys. >

Enter the start time with the number pad. >

Stop

Repeat the steps described in the “Start” section in order to set the ending time (except with station- >

change-timer.)

Repeat

Select the “Wdh” column with the arrow keys. >

Press the “OK” key. A selection window with different repeat suggestions appears. >

Choose the desired function with the up and down arrow keys. >

By pressing the “OK” key, the setting is saved. >

Saving data in memory

After you‘ve completed programming, press the yellow function key, “Save,” in order to save the data >

in memory.

Ending timer programming

By pressing the TV/Radio key, you return to normal operation mode.

Further information is available on the web at www.technistat.com.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Technisat DigiPal 2 TX e DVB-T in the language / languages: English, French, Italian, Spanish as an attachment in your email.

The manual is 6,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technisat DigiPal 2 TX e DVB-T

Technisat DigiPal 2 TX e DVB-T User Manual - German - 70 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Technisat DigiPal 2 TX e DVB-T Manual

Product: