622409

Technics SUR1EB Manual

23
Zoom out
Zoom in
Previous page
1/240
Next page
23
English
You can automatically link this unit with the SE-R1 and
operate them easily with the remote control.
Preparation
1 Connect this unit and the SE-R1 with cables for system
control. (> 9)
2 Set the input selector knob on the SE-R1 to [DIGITAL].
3 Press the unit on/off button on this unit and the SE-R1 to
the [ ] position.
4 If “Digital Link” is set to “Off”, change the setting to “On”.
∫ Switching this unit and the SE-R1 to
on/standby simultaneously
≥If you point the remote control at this unit and press [Í]
when this unit and the SE-R1 are in standby mode, this unit
and the SE-R1 will be turned on simultaneously.
≥If you point the remote control at this unit and press [Í]
when this unit and the SE-R1 are turned on, this unit and
the SE-R1 will simultaneously enter standby mode.
∫ Measuring the characteristics of the
amplifier and correcting its output
You can operate using the remote control of this unit.
∫ Adjusting Bass/Middle/Treble
You can adjust the tone of the SE-R1 with this unit. Each
tonal range (Bass/Middle/Treble) can be adjusted.
1 Press [SETUP].
2 Press [3, 4] repeatedly to select “Tone Control” and
then press [OK].
3 Press [3, 4] to select “On (adjustment)” and then press
[OK].
4 Press [3, 4] to select “BASS” (Bass), “MID” (Middle) or
“TREBLE” (Treble).
5 Press [2, 1] to adjust the level and then press [OK].
≥ Each level can be adjusted between “s10” and “r10”.
≥ For information on the operations of the SE-R1, please also refer
to its operating instructions.
Troubleshooting
Before requesting service, make the following checks. If you
are uncertain about some of the check points, or if the
solutions indicated in the following guide does not resolve
the issue, then consult your dealer for instructions.
Heat buildup of this unit.
≥This unit becomes warm when used for a long time. This is
not a malfunction.
Do you have the latest firmware installed?
≥Panasonic is constantly improving the unit’s firmware to
ensure that our customers are enjoying the latest
technology. (> 22)
A “humming” sound can be heard during
playback.
≥An AC mains lead or fluorescent light is near the cables.
Keep other appliances and cords away from the cables of
this unit.
No sound.
≥Check the volume of the connected device (amplifier, etc.).
≥Check to see if the cable connections to the input and
output terminals are incorrect. If this is the case, turn off
this unit and reconnect the cables correctly.
≥Check to see if the correct input source is selected.
≥Insert the plugs of the cables to be connected all the way
in.
≥When “Digital Output”, “Analog Output” and “Digital Link”
are set to “Off”, no sound will be output. Change the setting
of the output terminal to be used to “On”. (> 20)
≥Playback of multi-channel content is not supported.
≥The digital audio input terminals of this unit can only detect
linear PCM (LPCM) signals. For details, refer to the
operating instructions of the
connected
device.
Using the system control
function
To return all settings to the factory defaults
When the following situations occur, reset the memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
1 Press [SETUP].
2 Press [3, 4] repeatedly to select “Initialization” and
then press [OK].
3 Press [3, 4] to select “Yes” and then press [OK].
4 Press [3, 4] to select “Yes” and then press [OK]
again.
General
(23)
SU-R1-SQT0463_EBEG_mst.book 23 ページ ２０１５年６月１８日　木曜日　午前１１時５４分
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SUR1EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SUR1EB in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 8,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technics SUR1EB

Technics SUR1EB User Manual - Polish - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info