682965
24
Zoom out
Zoom in
Previous page
1/248
Next page
English
(24)
Before requesting service, make the below
checks. If you are in doubt about some of the
check points, or if the remedies indicated in the
chart do not solve the problem, contact your
dealer.
No power.
Is the AC mains lead plugged in?
Plug the mains lead in firmly. (
14)
There is power but no sound.
Sound is weak.
Are connections to the amplifier/receiver’s
PHONO terminals correct?
Connect the PHONO cables to the amplifier’s
PHONO terminals. (
14)
Left and right sounds are reversed.
Are the stereo connection cable connections
to the amplifier or receiver reversed?
Double check all connections. (
14)
Are connections of the head shell's lead wires
to the cartridge terminals correct?
Double check all connections. (
11)
Humming is heard during play.
Are there other appliances or their AC mains
lead near the stereo connection cable?
Separate the appliances and their AC mains
lead from this unit.
Is the earth lead connected?
Make sure the earth lead is correctly
connected. (
14)
The Strobe light or the blue
indicator blinks.
Perform the following operation when the
strobe light or the blue indicator blinks.
The symptom may be improved.
Turn [ON/OFF] to OFF.
Pull out the power plug, wait for three
seconds, and then insert the plug again.
Turn [ON/OFF] to ON and press
[START-STOP] to rotate the turntable.
If the strobe light or the blue indicator blinks
again, check which one is blinking and
contact our service representative.
Troubleshooting guide
Updating the firmware
To improve operation or add new functions,
the firmware for the unit is updated on an as
needed basis.
Before updating
From the support website, download the
firmware for version upgrade and create a
USB memory for version upgrade.
See the following website for how to create
a USB memory for version upgrade.
www.technics.com/support/firmware/
1
Turn [ON/OFF] to OFF and
remove the turntable.
(
13)
2
Connect the USB memory for
version upgrade to UPDATE
terminal of the
unit.
3
Turn [ON/OFF] to ON.
When update is
started, the update
lamps light up from
left to right.
4
Check that all of the four update
lamps are lit, and then turn
[ON/OFF] to OFF.
It takes approximately 120 seconds to
update the firmware.
5
Remove the USB memory.
Attention
Do not press [START-STOP] when the
turntable is removed.
Use a USB memory with FAT16 or FAT32
format.
Do not connect any USB device other than
the USB memory for version upgrade to the
UPDATE terminal of this unit.
No USB device can be charged from the
UPDATE terminal of this unit.
If after connecting the USB memory and
turning [ON/OFF] to ON, the update lamps
fail to light up within 15 seconds or they are
blinking, see the following website.
www.technics.com/support/firmware/
UPDATE
UPDATE
terminal
SERVICE
ONLY
Update lamps
24
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SL1200G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SL1200G in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 22,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info