682966
21
Zoom out
Zoom in
Previous page
1/28
Next page
Getting started
English
(21)
1
2
Armlift
screw
Armlift
Armlift height
Make an adjustment according to your
cartridge if necessary.
Preparation
Put a record on the turntable.
Remove the stylus cover, taking care not
to damage the stylus, then release the arm
clamp.
Lift the cue lever and move the tone arm over
the record.
1
Check the armlift height (distance
between the stylus tip and record
surface).
If adjustment is needed, go to
step
2
.
The armlift height is factory-adjusted to
8 to 13 mm.
2
Return the tone arm to the arm
rest and fix it with the arm clamp.
Turn the adjustment screw.
Turning the screw clockwise lowers the
armlift.
Turning the screw anti-clockwise raises
the armlift.
21
TORQUE
BRAKE
S
F
L
H
BRAKE button
S (Slow)
F (Fast)
Torque button
L (Low)
H (High)
Confirmation lamp
Press the centre of the button lightly.
Startup speed
You can select from three options of the startup
speed (the time to reach the constant speed) after
[START-STOP] is pressed and the torque gain at the
constant speed.
(Factory setting: 3)
[3] Fast startup
[1] Slow startup
The confirmation lamp blinks the specified number
of times according to the current setting when you
press the H or L torque button.
To change the setting, press the H or L torque
button while the lamp is blinking.
Example: If the current setting is [3] and you
press the L button twice, the setting will
change to [1].
After you press the torque button, the
confirmation lamp blinks the specified number of
times showing the new setting, stays lit for two
seconds and then goes off.
Brake speed
You can select from five options of the brake speed
to stop the turntable after [START-STOP] is pressed.
(Factory setting: 5)
[5] Stops fast
[1] Stops slowly
The confirmation lamp blinks the specified number
of times according to the current setting when you
press the F or S brake button.
To change the setting, press the F or S brake
button while the lamp is blinking.
Example: If the current setting is [5] and you
press the S button twice, the setting will
change to [3].
After you press the brake button, the confirmation
lamp blinks the specified number of times showing
the new setting, stays lit for two seconds and then
goes off.
Adjusting the turntable startup/
brake speed
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SL-1200GR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SL-1200GR in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info