536239

Technics SB-M01 Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
6
ENGLISH
ESPAÑOL FRANÇAIS
SVENSKA
Attaching the aluminum stand (included)
See pages 2 and 3 for details about the parts ( – ).
The speakers will sit steadier and better acoustic effects will be
achieved if the stand is fitted.
Attach the insulators ( and ) to the stand.
Do not attach insulator if you want to face the speakers up-
ward and bring the sound closer to the listening position.
Attach the stand to the base of the speaker.
(Lay the speaker on cloth to avoid scratches.)
Lift the speaker when moving it to avoid scratching floor surfaces.
Connections
•Before making the connections, switch OFF the power to the ampli-
fier.
•Check that a speaker with an impedance of 6 Ω can be connected
to the speaker terminals of the amplifier.
•Be sure to connect only positive (+) wires to positive (+) terminals,
and negative (–) wires to negative (–) terminals.
Amplifier (not included)
Right speaker
Left speaker
Speaker cables (not included)
Connecting the speaker cable to the speaker
Strip the outer covering from end of the cable to a length of ap-
proximately 15 mm and twist the center wire.
Turn the speaker terminal knob to the left until the hole ( ) is
visible.
Insert the center wire into the hole, and then turn the knob to the
right to secure the cable.
If using a commercially-available 4-mm plug cable ( )
Fully tighten the speaker terminal knob, and then insert the end of the
plug cable into the top of the knob.
CAUTION
E
To prevent damage to circuitry, never short-circuit positive (+) and
negative (–) speaker wires.
Colocación de la base de aluminio (incluida)
Consultar las páginas 2 y 3 para tener detalles de las piezas ( – ).
Si se coloca la base, los altavoces quedarán instalados de forma
más estable y mejorarán los efectos acústicos.
Colocar los aisladores ( y ) en la base.
No ponga el aislador si desea colocar los altavoces hacia
arriba y acercar más el sonido la posición de escucha.
Colocar la base en la parte inferior del altavoz.
(Poner el altavoz encima de un paño para impedir que se raye.)
Nota
Levantar el altavoz al trasladarlo de sitio para impedir rayar la superficie
del suelo.
Conexiones
•Antes de realizar las conexiones, desconectar la alimentación del
amplificador.
•Verificar que se puede conectar un altavoz de una impedancia de
6 Ω en los terminales de altavoces del amplificador.
•Asegurarse de conectar sólo los cables positivos (+) en los
terminales (+) y los cables negativos (–) en los terminales (–).
Amplificador (opcional)
Altavoz derecho
Altavoz izquierdo
Cables de altavoces (opcional)
Conexión de un cable de altavoz a un altavoz
Pelar el extremo del cable aproximadamente unos 15 mm y
retorcer el conductor central.
Girar la perilla del terminal del altavoz hacia la izquierda hasta
que el orificio ( ) quede a la vista.
Insertar el conductor central en el orificio, y luego girar la perilla
hacia la derecha para asegurarlo.
Si usa un cable con enchufe de 4 mm de venta en
comercios ( )
Apretar bien la perilla del terminal del altavoz, y luego insertar el
extremo del cable con enchufe en la parte de arriba de la perilla.
PRECAUCIÓN
E
Para no dañar el circuito, nunca se debe permitir que los conductores
de altavoces positivo (+) y negativo (–) hagan cortocircuito.
R
L
A
B
R L
Front
Parte delantera
Avant
Framsida
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SB-M01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SB-M01 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technics SB-M01

Technics SB-M01 User Manual - English - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info