536127
3
Zoom out
Zoom in
Previous page
1/4
Next page
RQT5460
3
Operation
Set the low pass filter, volume and phase to suit characteristics of
the speaker and SB-AS100 combination.
1 Set [POWER] to the “ ON” position.
The unit is now in standby mode and the POWER indicator
turns red.
When a signal is received the unit turns ON automatically and
the indicator turns green.
The unit automatically switches to standby if a signal is not
received for approximately two (2) minutes
2 Set [LOW PASS FILTER] to a suitable
frequency. Refer to “Frequency re-
sponse by LOW PASS FILTER setting”.
3 Set [VOLUME] to a suitable level. Refer
to “Frequency response by VOLUME
setting”.
4 After playing some music, set [PHASE]
to “ NORMAL” or “ REVERSE”,
whichever position allows playback to
sound normal.
For your reference:
If subwoofer and front speaker phase are the inverse of one
another, they will tend to cancel each other out. Playback will
not be normal and sounds will seem muffled.
When settings are complete
The only operation you should have to perform daily is press
[POWER] to turn the unit ON/OFF.
If you reposition the system and the acoustics change, reset the unit
as necessary.
If the volume output is too loud, this unit's amplifier can be clipped,
causing output to sound unusual. Reduce the volume of the receiver
or amplifier or the volume of this unit if this occurs.
Frequency response by LOW PASS FILTER setting
Frequency response by VOLUME setting
Front
Rear
Note
CAUTION:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
of the following measures:
¡Reorient or relocate the receiving antenna.
¡Increase the separation between the equipment and receiver.
¡Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
¡Consult the dealer or an experienced radio/TV technician for
help.
Any unauthorized changes or modifications to this equipment
would void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SB-AS100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SB-AS100 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technics SB-AS100

Technics SB-AS100 User Manual - English - 32 pages

Technics SB-AS100 User Manual - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info