536237
19
Zoom out
Zoom in
Previous page
1/52
Next page
19
RQT5518
2
1
3
4
5
SA-DA10 SA-DA8
1
BALANCE
TOP MENU
DISPLAY
DVD
ENTER
MENU
STEREO
DELAY
SURROUND
SFC TEST
MUTING
DIMMER VOL
TV VOL
TV/AV
123
DIRECT TUNING/
DISC ENTER
456
10/–/– –
7
890
+
+
LEVEL
DISC/DECK
1/2
DVD 6CH
+
1
4
7
0
89
56
23
DIRECT TUNING/
DISC ENTER
VOLUME
MUTING
10/ENTER
DISC/DECK 1/2
MD
SOUND MODE
SFC
SLOW/
SEARCH
DELAY
TOP MENU
ENTER
MENU
DISPLAY RETURN
SUB TITLE
AUDIO ANGLE
+
LEVEL
TEST
GROUP
–+
DIMMERPAGE
-/--
DVD
2
3
4
5
3
4
5
2
TEST
TEST
SPEAKERS
AB
BI-WIRE
VOL
+
+
VOLUME
LEVEL
LEVEL
+
+
SA-DA10 SA-DA8
SA-DA10 SA-DA8
SA-DA10 SA-DA8
SA-DA10 SA-DA8
SPEAKERS
A
LCRRSLSSW
C
RS LS SW
Preparation
Preparatory steps
Adjusting speaker output level
Adjust speaker level so the output from all the speakers is the
same apparent level when sitting where you would normally enjoy
a source.
1 Press [A] or [BI-WIRE] to turn on
SPEAKERS.
A or BI-WIRE refer to the speaker terminals at the rear of
the unit.
You cannot adjust output level when SPEAKERS B is
selected.
2
by remote control only
Press [TEST] to output the test signal.
“TEST” appears on the display.
The signal is output from each speaker in order for about
two seconds each:
L: Front speaker (left)
C: Center speaker
R: Front speaker (right)
RS: Surround speaker (right)
LS: Surround speaker (left)
SW: Subwoofer
Speakers set as “NONE” or “NO” are skipped.
Note
DSP sound mode switches to SURROUND mode when the
test starts.
3
by remote control
Press [VOLUME (+ or –)] (SA-DA10) or
[VOL (– or +)] (SA-DA8) to set the
volume level normally used for
enjoying the source.
Note
Use [BALANCE] if the left right balance of the front
speakers is off.
4
by remote control only
Press [LEVEL] to select the speaker
channel to adjust.
The current level appears on the display.
Press again to change the speaker channel.
Speakers set as “NONE” or “NO” are skipped.
5
by remote control only
Press [+] or [–] to adjust the level to
the same apparent level as the front
speakers.
The four channels can be adjusted between –10 dB and
+10 dB, with zero being the current level of the front
speakers.
6 Repeat 4 and 5 for each speaker
channel.
To stop the test signal
Press [TEST].
Note
The test signal will not be output if VGCA is ON (a page 27).
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SA-DA8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SA-DA8 in the language / languages: English as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Technics SA-DA8

Technics SA-DA8 User Manual - English - 52 pages

Technics SA-DA8 User Manual - English - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info