Manual Team TeCom-IP3 (page 13 of 27) (English, German, Italian, Spanish)

749145

Zoom out

Zoom in

1/27

24 25

EnglishEnglish

VOX

VOX allows signal transmission without pressing the PTT key. As soon as the signal

strength reaches the programmed signal threshold (level 1-9), the radio automatically

switches into transmission mode. Once the signal ends, the radio remains in VOX mode

for a programmed duration (delay time 0,3 / 0,5 / 1 / 1,5 / 2 / 3 s).

The parameters VOX delay and VOX sensitivity (level) can be programmed via software.

To activate/deactivate the VOX function press the double-function-key PF1/2 that is

programmed with the VOX function.

Revert

This function is only of use for the commercial radio versions UHF- and VHF-COM,

when using differing rx and tx frequencies.

With this function activated, the rx and tx frequencies are reverted. To revert again

to the prior state, the function has be deactivated

Offline

This function is only of use for the commercial radio versions UHF- and VHF-COM,

when using differing rx and tx frequencies for repeater communication.

When activated, the tx frequency will be set to the tx frequency. Communication

through the repeater is then deactivated but local communcation with close-by par-

ticipants is possible.

Power

The tx powers High and Low can be selected. With the PMR and FreeNet version

the maximum tx power is 500 mW. The tx powers for the commercial radio versions

UHF-COM (max. 4 W) and VHF-COM (max. 5 W) can be programmed, according

to the licence, via software.

Scan

All channels that are activated for channel scanning will be contiuously searched

until a signal has been detected.

Adding and deleting to the scan list is done via the optional software T-UP31.

Priority Scan

Between each of the channels of the scan list, the priority channel is added. The

priority channel is determined with the software T-UP31.

Instead of a regular scan, e.g. 1 - 2 - 4 - 5 - 7 - 8, the priority scan will scan in the

following order, if channel 4 is the priority channel: 4 -1- 4 - 2 - 4 - 5- 4 - 7- 4 - 8.

Alarm tone button (7)

Press the orange alarm tone (7) shortly and a constant alarm tone is emitted. This

tone is audible by all stations that operate on the same channel. To stop the alarm

tone, press the alarm tone button again.

SOFTWARE FUNCTIONS

The following functions and settings are managed via software. The radio versions PMR

and FreeNet can be programmed with the software version T-UP31 PMR-FN and the

commercial radio versions UHF- and VHF-COM with the software T-UP31 COM.

Receiving Frequency (RX Freq) / Transmission Frequency (TX Freq)

With the radio versions PMR and FreeNet, the available frequencies are fixed, RX

and TX frequency of one channel are always the same.

With the commercial radio versions UHF- and VHF-COM, the assigned frequency

will be programmed manually. The RX and TX frequency of a channel can differ.

CTCSS/DCS codes for Receiving Frequency (Decode) and Transmission Frequency

(Encode)

There are 50 CTCSS and 210 DCS (105 DQS-N and 105 DQS-I) codes available.

They can be assigned individually to the RX frequency and the TX frequency for

each channel.

Busy Channel Lockout (BCL)

With the Busy Channel Lockout function, transmission is blocked once a signal is

present on the selected channel.

TX Power Switch (Tx Power)

For PMR and FreeNet, the tx power setting HIGH is fixed to 500 mW. For the com-

mercial radio versions UHF- and VHF-COM, the settings HIGH and LOW can be

programmed, according to the assigned values of the licence, via software.

Bandwidth (N/W) - only COM-Version

For PMR and FreeNet, the bandwidth is fixed to 12.5 kHz (N) according to govern-

mental regulations. For the commercial versions the settings N(12,5 kHz) and W

(25 kHz) are available.

Scan (Scan Add/Del)

The available channels are scanned for signals according to the scan list. Each chan-

nel may be added (Add) or excluded (Del) from this scan list. Please note that at the

scan list must contain at least two channels for the scan function to work.

Squelch (SQ Level 0-9)

The squelch level determines what strength a signal must have to unmute the

speaker. The higher the level, the higher the threshold. At the level 0, the squelch is

deactivated, the typical constant noise is audible. At level 9, the signal must be

very strong to unmute the speaker.

tecom-ip3_man_V5_18-2-14_Layout 1 14.02.2018 10:37 Seite 24

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team TeCom-IP3 in the language / languages: English, German, Italian, Spanish as an attachment in your email.

The manual is 0,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team TeCom-IP3 Manual

Product: