487583

Team ST 46 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
ge
the page numbering. Keep the language integrity.
9 TEAM ST 46 E - 100124
Assembly page 9/44
Fax +32 2 359 95 50
ASSEMBLING THE VACUUM CLEANER
Always remove the plug from the power socket before fitting or removing accessories!
Insert the hose connector into the hose connection inlet until it locks. To remove the hose,
press the sides of the hose connector and pull at the hose connector.
Fit the tube to the handle.
Fit the tube to the floor brush.
Removing tube and accessories: to remove the accessories, pull firmly apart.
The floor brush is ideal for the daily cleaning of carpets and hard floors.
Setting with the bristles inside for cleaning carpets.
Setting with the bristles outside for cleaning hard floors.
The appliance is delivered with the following accessories:
a crevice tool: for radiators, crevices, corners, baseboards
and between cushions.
an upholstery brush: for curtains, cushions, edges, doors,
mattresses etc.
a parquet floor brush: to vacuum wooden floors.
OPERATION
Pull out a sufficient length of power cord and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable length. Do not extend the cable
beyond the red mark. Switch on the appliance by pressing the ON/OFF switch with your
foot.
It is advisable to set the electronic power regulator to the minimum position MIN before
switching on the appliance. By turning the regulator button, the suction power can be
adjusted. You can also adjust the suction power by using the wind-force adjuster on the
handle. Use a low suction power for furniture and other delicate surfaces and use high
suction power for fitted carpet and other floors.
AFTER USE
Stop the vacuum cleaner by pressing the ON/OFF switch.
Unplug the appliance from the power supply.
Simply press the cable rewind button to activate the cable rewind mechanism.
The carrying handle can be used to move the appliance. Never use the handle of the
dust container to carry the appliance!
After use we advise you to empty the dust collector to avoid smells and mildew that could
be caused by damp dust particles that may have been vacuumed, and also to
guarantee an optimal efficiency during the next use. To do so, see below.
EMPTYING THE DUST COLLECTOR
Press the release button of the dust container and pull the dust container out.
Remove the lid of the dust container and spill the rubbish.
Put the lid back on the dust collector and put the dust collector back in the appliance
until it locks in place.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team ST 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team ST 46 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info