487579

Team ST 42 Manual

10
Zoom out
Zoom in
Previous page
1/28
Next page
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must be reproduced and folded in order to
obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). The
pages must be folded in order to keep the good numbering
when you turn the pages of the I/B . Don’t change the page
numbering. Keep the language integrity.
10 TEAM ST 42 ET - 080509
Assembly page 10/28
Fax +32 2 359 95 50
ASSEMBLING THE VACUUM CLEANER
Remove all packaging material from the appliance and its accessories.
Insert the hose (3) in the connection inlet of the appliance (9), and press until it clicks (Fig.
1). To remove the hose, press its release buttons and pull at it.
Assemble the handle of the flexible hose (3) on the upper part of the tube (2) and then
assemble the floor brush (1) on the other end of the tube, as indicated on figures 2 and 3.
The length of the telescopic tube can be adjusted. To do so, slide the adjusting button
and pull the desired tube length, then release the button (fig. 4).
The floor brush (1) possesses 2 positions which allow you to clean all kinds of surfaces very
easily, simply by changing the position adequately:
Setting with the bristles inside for cleaning carpets.
Setting with the bristles outside for cleaning hard floors.
The appliance is delivered with a wooden floor brush to vacuum wooden floors. Attach
the brush to the tube (2).
OPERATION
First of all, check if the filters are placed properly in the appliance, as vacuum cleaning
without filter might damage the motor of the appliance irreparably (see paragraph
FILTERS for their use and installation).
CAUTION: In order to avoid important electric disturbance when starting the appliance, it
is fitted with a "soft start" feature. This feature prevents the motor from starting at its full
power. As a result, there might be a short time-lag (1 or 2 seconds) between the moment
you press the on/off switch and the moment the appliance really starts. This is normal.
Pull out a sufficient length of power cord and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable length. Do not extend the cable
beyond the red mark. Switch on the appliance by pressing the ON/OFF switch (8).
You can adjust the suction power manually with the wind force adjuster, or with the
electronic power control switch (7). Use a low suction power for furniture and other
delicate surfaces and use high suction power for fitted carpet and other floors.
With the accessory supplied you can clean surfaces that are hard to reach, such as
furniture (use the crevice tool) and delicate surfaces such as curtains (use the small brush).
This accessory can be mounted on the handle or on the tube. You can find the accessory
on the bottom of the appliance. To store it, you just need to insert it in the compartment
foreseen to that end on the bottom of the appliance.
AFTER USE
Stop the vacuum cleaner by depressing on the on/off switch.
Disconnect plug from electrical outlet.
Simply press lightly with your foot on cable rewind button on top of the cleaner. If the cord
does not enter completely in the appliance, pull 50 cm of the power cord out of the
appliance and try again.
After use we advise you to empty the dust collector to avoid smells and mildew that could
be caused by damp dust particles that could have been vacuumed, and also to
guarantee an optimal efficiency during the next use. To do so, see below.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team ST 42 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team ST 42 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info