Manual Team ST 41 (page 12 of 31) (English, German, Dutch, French, Spanish)

487578

Zoom out

Zoom in

1/31

Generated by Unregistered Batch DOC TO PDF Converter

2011.3.804.1511, please register!

Copies of the I/B. Please reproduce them without any changes

except under special instruction from Team International

BELGIUM. The page must be reproduced and folded in order to

obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). The

pages must be folded in order to keep the good numbering

when you turn the pages of the I/B . Don’t change the page

numbering. Keep the language integrity.

12 TEAM ST 41 E - 080508

Assembly page 12/31



Fax +32 2 359 95 50

ASSEMBLING THE VACUUM CLEANER

 Remove all packaging material from the appliance and its accessories.

 Insert the hose (3) in the connection inlet of the appliance (9), and press until it clicks (Fig.

1). To remove the hose, press its release buttons and pull at it.

 Assemble the handle of the flexible hose (3) on the upper part of the tube (2) and then

assemble the floor brush (1) on the other end of the tube, as indicated on figures 2 and 3.

 The floor brush (1) possesses 2 positions which allow you to clean all kinds of surfaces very

easily, simply by changing the position adequately:

Setting with the bristles inside for cleaning carpets.

Setting with the bristles outside for cleaning hard floors.

OPERATION

 First of all, check if the filters are placed properly in the appliance, as vacuum cleaning

without filter might damage the motor of the appliance irreparably (see paragraph

FILTERS for their use and installation).

 CAUTION: In order to avoid important electric disturbance when starting the appliance, it

is fitted with a "soft start" feature. This feature prevents the motor from starting at its full

power. As a result, there might be a short time-lag (1 or 2 seconds) between the moment

you press the on/off switch and the moment the appliance really starts. This is normal.

 Pull out a sufficient length of power cord and insert the plug into the power socket. A

yellow mark on the power cable shows the ideal cable length. Do not extend the cable

beyond the red mark. Switch on the appliance by pressing the ON/OFF switch (8).

 You can adjust the suction power manually with the wind force adjuster (fig. 4), or with the

electronic power control switch (7). Use a low suction power for furniture and other

delicate surfaces and use high suction power for fitted carpet and other floors.

 With the accessorie supplied you can clean surfaces that are hard to reach, such as

furniture (use the crevice tool) and delicate surfaces such as curtains (use the small brush).

This accessorie can be mounted on the handle or on the tube. You can find the

accessorie on the bottom of the appliance. To store it, you just need to insert it in the

compartment foreseen to that end on the bottom of the appliance.

AFTER USE

 Stop the vacuum cleaner by depressing on the on/off switch.

 Disconnect plug from electrical outlet.

 Simply press lightly with your foot on cable rewind button on top of the cleaner. If the cord

does not enter completely in the appliance, pull 50 cm of the power cord out of the

appliance and try again.

 After use we advise you to empty the dust collector to avoid smells and mildew that could

be caused by damp dust particles that could have been vacuumed, and also to

guarantee an optimal efficiency during the next use. To do so, see below.

EMPTYING THE DUST COLLECTOR

It is necessary to remove the hose from the connection inlet first.

 Press the release button (4) on the lid of the appliance and pull open the lid. Then pull out

the dust collector (fig. 5, step 1 and 2).

 Press the unlocking button on the handle of the dust collector (fig. 5, step 3) to open the

dustcup's lower cover and spill the rubbish.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team ST 41 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team ST 41 Manual

Product: