487310

Team ST 16 ET Manual

8
Zoom out
Zoom in
Previous page
1/28
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don‟t change
the page numbering. Keep the language integrity.
8 TEAM ST 16 ET - 071005
Assembly page 8/28
Fax +32 2 359 95 50
ASSEMBLING THE VACUUM CLEANER
Always remove the plug from the power socket before fitting or removing accessories!
Insert the hose connector into hose connection inlet until it locks (fig. 1). To remove the
hose, press the sides of the hose connector and pull at the hose.
When removing hose assembly, pull out hose connection wand with pushing down two
connection buttons.
Fit the tube to the handle (Fig. 2).
Fit the tube to the floor brush (Fig. 3).
Removing telescopic tube and accessories: to remove the accessories, pull firmly apart.
The floor brush is ideal for the daily cleaning of carpets and hard floors.
Setting with the bristles inside for cleaning carpets.
Setting with the bristles outside for cleaning hard floors.
The appliance is delivered with the following accessories:
a crevice tool: for radiators, crevices, corners, baseboards
and between cushions.
an upholstery brush: for curtains, cushions, edges, doors,
mattresses etc.
OPERATIONS
Pull out a sufficient length of power cord and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable length. Do not extend the cable
beyond the red mark. Switch on the appliance by pressing the ON/OFF switch with your
foot.
It is advisable to set the electronic power regulator to MIN before switching on the
appliance. By turning the regulator button, the suction power can be adjusted. You can
also adjust the suction power by using the wind-force adjuster on the handle (Fig 4). Use a
low suction power for furniture and other delicate surfaces and use high suction power for
fitted carpet and other floors.
AFTER USE
Stop the vacuum cleaner by pressing the ON/OFF switch.
Unplug the appliance from the power supply.
Simply press the cable rewind button to activate the cable rewind mechanism.
REPLACING THE DUST BAG AND CLEANING THE FILTERS
Filters
The filter system consists of: 1 motor filter (in front of the motor in the dust compartment)
1 air filter, to vacuum the smallest particles (on top of the motor in
the dust compartment)
It is necessary to clean the filters regularly to avoid operating problems.
Paper dust bag
The dust bag level indicator indicates when the dust bag should be replaced.
The hose might get blocked by a larger object. In this case the dust bag level indicator will
be red. However this does not mean that you have to replace the dust bag. Just remove
the object which blocks your tube or flexible hose, and your appliance will function
properly again. Do not forget to unplug the appliance before removing the blocking
object. Replace the dust bag when the dust bag level indicator is completely red.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team ST 16 ET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team ST 16 ET in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info