487286

Team SIS 11 Manual

11
Zoom out
Zoom in
Previous page
1/52
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity.
Fax +32 2 359 95 50
First sort out the fabrics according to ironing temperature: wool with wool, cotton with
cotton, etc.
The iron heats up quicker than it cools down. Therefore, start ironing the articles requiring
the lowest temperature such as those made of synthetic fibres. Then progressively increase
the temperature.
•
•
•
•
•
•
•
•
•
•
•
If the article is made of a mixture of different fibres, you must always select the ironing
temperature corresponding to that of the fibre requiring the lowest temperature.
(E.g. an article consisting of “60% polyester and 40% cotton” should be ironed at the
temperature indicated for polyester and without steam.)
If you do not know the kind of fabric(s) the article has been made of, find a spot which will
be invisible when wearing or using the article to try out the ironing temperature. (Always
start at a low temperature and increase to one which gives the required results.)
Pure woollen fabrics (100% wool) may be pressed with the iron set to a steam position. It is
recommended to apply a burst of steam and use a dry pressing cloth between the
woollen article and the iron.
When ironing with steam (see paragraph “Steam ironing”), the fabric might shine. You can
prevent it by ironing the reverse side of the article or interposing a slightly humid cloth
between the article and the soleplate.
Velvet and other fabrics that rapidly acquire shiny spots should be ironed in one direction
only (the one of the nap), applying only light pressure. Always keep the iron moving.
Iron the reverse side of synthetic materials and silk; it is not advisable to use steam as this
may cause stains.
FILLING THE WATER TANK (FOR STEAM IRONING)
1. Put the base on a stable surface.
2. Open the water tank by unscrewing the cap (5) and fill the water tank with clear water
using the provided funnel. You can use tap water, but we advise you to use demineralised
water. The water tank can contain 0.8 litre of water at the maximum.
3. Close the cap (5) of the water tank by screwing it back on.
4. Never use vinegar, detergents or other chemical products.
FILLING THE WATER TANK DURING USE
USE CAUTION! WHEN THE APPLIANCE IS IN OPERATION, THE WATER TANK IS UNDER PRESSURE DUE
TO HOT STEAM.
IN THE FIRST PLACE, MAKE SURE THAT THERE IS NO MORE STEAM IN THE WATER TANK. TO DO SO,
BLEED THE TANK - THE BASE AND THE IRON STILL ENERGIZED – BY PRESSING THE BUTTON (6) UNTIL
NO MORE STEAM ESCAPES. THEN SWITCH OFF THE BASE AND THE IRON. UNSCREW THE CAP
SLOWLY AND CAREFULLY IN ORDER TO CHECK IF THERE IS NO STEAM AT ALL ANYMORE (IF THERE
IS STILL SOME RESIDUAL STEAM, A WHISTLING NOISE WILL BE MADE), THEN UNSCREW THE CAP
COMPLETELY. LET THE TANK COOL DOWN FOR A FEW MINUTES, THEN REFILL IT. BE CAREFUL: IF
YOU FILL IT TOO SOON, STEAM OR HOT WATER WILL ESCAPE FROM THE OPENING. IT IS
RECOMMENDED TO FILL THE TANK SLOWLY, ESPECIALLY AT THE BEGINNING. FINALLY, CLOSE THE
TANK WITH THE CAP. YOUR APPLIANCE IS READY FOR USE AGAIN.
STEAM IRONING
Fill the water tank with water.
As indicated on the temperature dial (8) and in the table, steam ironing is only possible at
higher ironing temperatures, so set the dial to
zz or zzz.
Plug in the appliance and press the power switch (10) to turn on the appliance.
Press the steam switch (11) to switch the boiler on.
Set the temperature dial of the iron (8) to the desired position. When the iron has reached
the desired temperature, its pilot light (1) will go out.
11 TEAM SIS 11 - 110221
Assembly page 11/52
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team SIS 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team SIS 11 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info