Manual Team MX-10 (page 8 of 29) (English, German, Dutch, French, Italian, Spanish)

749159

Zoom out

Zoom in

1/29

> no interference of the roadworthiness,

> good access to the controls of the car,

> sufficient air circulation to prevent overheating of the radio in transmit mode.

Please consider that the readability of the LC display (1) depends on the angle of view. Also,

an intensive solar radiation affects the readability of the display. Please check the best posi-

tion before the final installation.

Microphone

Plug the microphone-plug (20) into the 6-pin socket (15), located on the front panel. Pay

attention to proper placement. No transmission nor reception is possible without the micro-

phone. The pin assignment of the GDCH standard microphone plug is given below:

PIN 1 Modulation

PIN 2 Loudspeaker

PIN 3 PTT

PIN 4 Up/Down

PIN 5 Ground

PIN 6 +12 Volt

Solder side view of the microphone connector or top view of the microphone plug.

The standard microphone , which is equipped with channel selector and signal tone keys, is

included with the MX-10. This microphone offers is the best selection for the MX-10.

Power source

Before connecting the unit to a suitable power source via the fused DC power cable (25), the

device must be switched off by turning the volume control (10) [OFF/VOL] counterclockwise

to the very end.

Then, connect the two naked leads at the end of the cable with the supply voltage of the

car/lorry battery. The unit is designed to operate with 12 volts or 24 volts and a negative

ground electrical system. Lay the cable as far as possible away from aggregates which can

cause interference. Pay attention to the correct polarity during the connection.

BLACK connect to - MINUS / ground of the car battery.

RED connect to 12/24 volts + PLUS of the car/lorry battery.

After proper connection of the microphone, the aerial and power source, radio operation can

be started.

Scope of Delivery

1 x MX-10 mobile radio

1 x UP/DOWN microphone with clamping holder

1 x detachable cigarette-lighter adapter plug with fuse

1 x under-dash mounting kit

1 x Declaration of Conformity

1 x manual

English English

14 15

Setting up the TEAM MX-10

Installation of a CB antenna

The antenna is an important part of a cb mobile radio system. The type of antenna and its

location has a great effect on the range of operation. Please consider the following criteria for

selecting the best location and installation of your antenna:

> Make sure that the antenna is designed for radio operation on 27 MHz.

> The location of the antenna should be as high as possible without any obstacles nearby.

> The aerial cable should not be damaged and the plugs should be properly connected.

> Make sure that the antenna cable is not bent too much.

> The bigger the mechanical size of the antenna, the higher the range of operation.

When you install a mobile antenna please note the following advices:

> The antenna should be fixed in the center of a bigger part of the coachwork.

> The mobile antenna coil should have the closest possible contact with a conducting metallic

surface of the bodywork of the car.

There are also some other possibilities to fix the antenna onto the car without the necessity

to drill a hole into the bodywork of your car, e.g. mounting the antenna onto the gutter, mount-

ing the antenna onto a holder on the cover of the boot or using an antenna with a magnetic

foot or using a windscreen antenna.

For base-station operation we recommend a stationary antenna on the roof, for example the

TEAM ECO 050 or ECO 200.

> Please don't mount the CB antenna nearby a radio or TV antenna to prevent interference

of radio or TV reception.

> Keep an eye on power lines running along nearby when mounting the antenna on the roof.

" DANGER "

> The base-station antenna has to be connected via a lightning arrester.

> All connected cables including the antenna cable must not exceed a length of 3 m.

Aerial Connection

Before pressing the transmit key, a suitable aerial must be connected. The PL259 plug of the

aerial cable ( coax ) is connected to the SO239 socket (24) on the rear panel. Make sure, that

all plugs are firmly tightened and properly soldered. Unsatisfactory connections can damage

the radio and will reduce the range of operation.

The antenna should be matched with the radio, otherwise a part of the transmit power will be

reflected at the antenna and will not be radiated. This causes also a drop in the range of oper-

ation. The matching can be carried out by a length adjustment of the antenna radial for a mini-

mal SWR ratio which can be measured by a SWR meter (e. g. TEAM SWR 1180P). After the

measurement, the SWR meter should be removed from the antenna line.

Installation in the car

When you want to install the unit into your car, you can install it below the dashboard with the

included mounting bracket set.

Always mount the transceiver where the switches are easily accessible. Please consider for

determining the correct mounting position:

manual_MX-10_v1-7:RoadCOM manual.qxd 12/17/2014 8:45 AM Page 14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team MX-10 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team MX-10 Manual

Product: