487053

Team KA VT 7 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
9 TEAM KA VT 7 - 071011
Assembly page 9/32
Fax +32 2 359 95 50
ASSEMBLY
1. Place stand A (18) on stand B (19) to form an X-base.
2. Place the lower pipe (15) with pipe support (17) on the X-base and fix it with four screws
provided.
3. Loosen and remove the pipe connector (14) from the lower pipe (15). Slide the plastic
base cover (16) over the lower pipe on the base. Extend the upper (inner) pipe (13) and
slide the pipe connector (14) over the upper pipe onto the lower pipe and tighten.
4. Attach the motor (11) with speed regulator (12) onto the upper pipe (13). Ensure the
speed regulator is pushed fully onto the upper pipe and secured with the screws provided.
5. Loosen the guard mounting ring (6) from the motor housing (9).
6. Position the rear guard (7) firmly against the motor housing (9) and fasten by turning the
guard mounting ring (6) clockwise tightly.
7. Push the blade (5) along the motor shaft (8). Fasten it firmly with the cap (4) by turning
counter clockwise.
8. Hang the front guard (2) to the rear guard (7) with the position fixer (3) provided at the
front guard rim, and then clamp together with the clips provided.
9. To ensure that it is impossible to have access to the fan blade without using a tool, a screw
is provided with this appliance in order to attach both parts of the mesh guard together.
This screw must be tightened on the lower part of the guards. We will not be responsible
for any injuries in case this screw had not been tightened before using the appliance.
10. To change the height, loosen the pipe connector (13) and slide the upper pipe to a
suitable height. Then tighten the pipe connector (14) again.
OPERATION
This appliance is equipped with 3 ventilation speeds. To switch on the appliance, press
one of the speed knobs. To switch it off, press “0”.
Speed settings:
0 = OFF
1 = Low
2 = Medium
3 = High
This appliance also has an oscillation function:
Push the oscillation knob (10) to switch on the oscillation.
Pull the oscillation knob (10) to stop.
It is also possible to tilt the upper part of the appliance in order to adjust the airflow
direction vertically.
CLEANING AND CARE
Always disconnect the power supply cable from the power supply before carrying out any
cleaning operation.
To remove dirt from the plastic surfaces, use a soft damp cloth. Use a vacuum cleaner to
remove the dust from the guards without having to disassemble them.
Never immerse the fan in water or any other liquid.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team KA VT 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team KA VT 7 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info