487057

Team KA VT 15 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
9 TEAM KA VT 15 - 071011
Assembly page 9/32
Fax +32 2 359 95 50
ASSEMBLY
1. Loosen the fixing nut (16) from the lower pipe (14).
2. Insert the lower pipe (14) in the middle of the base (15) and tighten the fixing nut (16)
underneath the base (15) to fix the pipe to the base.
3. Slightly loosen the pipe fixing screw (13) and pull out the upper pipe (12) to the desired
length. Then tighten the pipe fixing screw (13).
4. Remove the fixing screw (11) located on the upper pipe and fit the motor housing (10)
with speed regulator into the upper pipe (12). Make sure the motor housing (10) is pushed
fully onto the upper pipe and that the hole of the upper pipe is in front of the hole located
on the motor housing. Attach the two parts with the fixing screw (11).
5. Loosen the guard mounting ring (6) from the motor housing (10).
6. Position the rear guard (7) firmly against the motor housing (9) and fasten by turning the
guard mounting ring (6) clockwise tightly.
7. Push the blade (5) along the motor shaft (8). Fasten it firmly with the cap (4) by turning it
counter clockwise.
8. Fit the front guard (2) and the rear guard (7) together with the position fixer (3) provided at
the front guard rim, and then clamp them together with the clips provided.
9. To ensure that it is impossible to have access to the fan blade without using a tool, a screw
is provided with this appliance in order to attach both parts of the mesh guard together.
This screw must be tightened on the lower part of the guards. We cannot be held
responsible for any injuries in case this screw had not been tightened before using the
appliance.
10. To change the height, loosen the pipe fixing screw(13) and slide the upper pipe to a
suitable height. Then tighten the pipe fixing screw (13) again.
OPERATION
This appliance is equipped with 3 ventilation speeds. To switch on the appliance, turn the
rotary speed regulator into the desired position. To switch it off, put it in “0” position.
Speed settings:
0 = OFF
1 = Low
2 = Medium
3 = High
This appliance also has an oscillation function:
Push the oscillation knob (9) to switch on the oscillation.
Pull the oscillation knob (9) to stop.
It is also possible to tilt the upper part of the appliance in order to adjust the airflow
direction vertically.
CLEANING AND CARE
Always disconnect the power supply cable from the power supply before carrying out any
cleaning operation.
To remove dirt from the plastic surfaces, use a soft damp cloth. Use a vacuum cleaner to
remove the dust from the guards without having to disassemble them.
Never immerse the fan in water or any other liquid.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team KA VT 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team KA VT 15 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info