487050

Team KA DV 2 Manual

7
Zoom out
Zoom in
Previous page
1/28
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the
good numbering when you turn the pages of the I/B. Don’t
change the page numbering. Keep the language integrity.
7 TEAM KA DV 2 - 091219
Assembly page 7/28
Fax +32 2 359 95 50
INSTALLATION
1. Take the mounting plate out of the upper canopy (unscrew the 2 left screws and unscrew the
2 right screws lightly). Then attach the mounting plate firmly to the ceiling (Fig. 1).
2. Make the upper canopy slide onto the rod and insert the electric wires in the rod (Fig. 2).
3. Check if the metallic demi-ball is fixed correctly to the end of the rod (Fig. 3). If necessary,
screw back the screw.
4. Put the rod onto the motor hanger. Then insert the perforated nail (Fig. 4) in the
corresponding holes.
5. Put the split pin in the hole situated at the end of the nail (Fig. 5).
6. Attach the rod to the motor by tightening the supplied screws (Fig. 6).
7. Attach the obtained motor block to the mounting plate and make sure that the guide of the
mounting plate enters into the slot of the metallic demi-ball (Fig. 7).
8. Connect the wires of the light to the connector foreseen to this end.
9. Attach the upper canopy to the mounting plate (Fig. 9).
10. Tighten the upper canopy to the mounting plate (tighten the 2 right screws and add the 2 left
screws) (Fig. 10).
11. Assemble the fan blades and the blade holders (the nice side of the blade holders has to be
on the same side as the nice side of the fan blades). Use the supplied screws and washers
(Fig. 11).
12. Attach the fan blades to the motor block. To do so, remove the screws and washers of the
motor block, put one of the 1/4 pieces of carton with 2 holes between the blades and the
motor block, then fix the blades with the washers and screws (Fig. 12).
13. Connect the 2 wires of the lamp holder to the 2 wires of the motor block (respect the colours).
Then attach the lamp holder to the motor block (remove the 3 screws and 3 washers, place
the lamp holder, then fix it with the 3 screws and 3 washers) (Fig. 13).
14. Fix the tulip-shaped glass lampshades on the lamp sockets (3 screws per lampshade), then
insert the light bulbs (max. 60W) (Fig. 14).
15. Connect the chain to the switch of the appliance.
INSTALLATION OF THE WALL SWITCH
1. Switch box
2. ACTIVE
3. NEUTRAL
1. Check to make sure there is no electric current in your
electric power supply.
2. Attach the switch box to the wall.
3. Connect the wires of your electric installation to the box as
indicated on the pictures.
L : Light
F : Fan motor
USE
Switch on your appliance and check the good functioning of your appliance.
The chain/wall switch controls the fan as follows:
A. Pulling once/ Position HI --> High speed
B. Pulling twice/ Position MED --> Medium speed
C. Pulling three times/ Position LOW --> Low speed
D. Pulling four times/ Position OFF --> Stop
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team KA DV 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team KA DV 2 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info