Manual Team hcs 3 (page 11 of 40) (English, German, Dutch, French, Italian, Portuguese, Spanish)

401533

Zoom out

Zoom in

1/40



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t change

the page numbering. Keep the language integrity.

11 TEAM HCS 3 N - 080304

Assembly page 11/40

Fax +32 2 359 95 50

top of the blades perpendicular to the skin and cut to the desired length (7). If necessary,

insist on the reluctant hair.

 When you get used to your hair clipper, you will be able to make layers simply by

changing the length of the combs in function of the cutting zone. These handling asks for

a special dexterity in order to obtain a correct result.

SHORT CUTS

 Always cut from the back of the neck to the crown, using the longest attachment comb.

Holding it flat against the head, slowly move the clipper up through the hair. Use the same

technique for the sides.

 For the front of the crown, cut the hair against the direction in which it grows. Then even it

up with the sides.

 For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head

over it. To taper hair down to the neckline, use closer cutting attachment combs. Comb

hair, check for uneven spots and outline neckline.

 The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (8).

LEVER

This lever has two main functions:

 Regulation of the cutting length because in the position short hair (lever pushed to the

front side) you can cut the length of the used combs or make outlining by pulling it to the

backside, you can make the cutting length longer (this allows middle cutting lengths

above the 4 delivered combs).

 Partial cleaning of the blades when in use by to and for motions in order to remove the

hair blocked in the blades.

MAINTENANCE

 Your clipper was carefully examined before leaving our factory to ensure that the blades

were oiled and aligned.

 Blades must be realigned if they have been removed for cleaning or replacement.

Therefore, as the lever is pushed to the front side in short hair position, the end of the top

blade teeth is

 Approximately 1.2 mm away from bottom blade. Compare your clipper blades with the

sketch (9).

 If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for

a few moments, turn off and unplug. Loosen screws slightly and turn the upper blade until

a correct alignment. Then tighten screws once the blades are aligned (10).

 Change the blades as soon as they become blunt.

 To clean the blades, use the small brush delivered with your appliance and if necessary,

remove them completely.

OIL

To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).

Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will

evaporate and leave the thick oil which may slow down the blades' motion.

ACCESSORIES

Your appliance is delivered with a complete set of hair accessories, which allows you to make

the desired hair cuttings: 1pair of scissors, 1 comb and 4 interchangeable combs to place on

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team hcs 3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team hcs 3 Manual

Product: