Manual Team HCS 2 (page 10 of 36) (English, German, Dutch, French, Italian, Portuguese, Spanish)

487010

Zoom out

Zoom in

1/36



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t change

the page numbering. Keep the language integrity.

Assembly page 10/36

Fax +32 2 359 95 50

IMPORTANT INFORMATION

This appliance is not for professional use. You should follow the requested breaks. Failure to

follow this instruction carefully may result in damage to the appliance. Please refer to the rating

label for the maximum continuous usage time (KB xx min where xx is the maximum usage time).

The breaks should last at least 10 minutes.

BEFORE YOU START

 Make sure that your clipper is clean, properly oiled and in perfect working condition.

Attention, if the blades are not properly oiled, your appliance will not work correctly.

 Place a towel around the neck of the person whose hair is to be cut to prevent hair from

falling inside the collar.

 Have the person sit on a chair so that his/her head is at your eye’s level.

 Comb the hair thoroughly and hold the clipper in a relaxed, comfortable grip. This will help

you maintain an accurate cutting control.

CUTTING HAIR WITH THE ATTACHMENT COMBS

To attach the comb, hold it with teeth up and snap comb attachment firmly to the bottom of

the clipper blade (see picture 1):

Attachment comb #1...leaves hair approx. 1/8" in length

Attachment comb #2...leaves hair approx. 1/4" in length

Attachment comb #3...leaves hair approx. 3/8" in length

Attachment comb #4...leaves hair approx. 1/2" in length

 In order to become accustomed to the length of each attachment comb we

recommend for the first use to place the attachment comb #4 and then to reduce the

length steadily until you obtain the desired length. Afterwards, you can place directly the

comb you want.

 For uniform cutting, never push or force the clipper through the hair at a fast pace. The

clipper works most efficiently when it works at its own speed.

 Once you placed the attachment comb on the hair clipper, cut the hair by placing the

comb teeth flat against the scalp (2). We recommend to proceed by small lengths in

order to avoid stuffing. Therefore you only have to remove the comb regularly by bending

it lightly outward. Then make the same movement but start lower than the point you

remove the clipper in order to obtain a homogeneous length.

 The cutting always happens by moving towards in the opposite side of the natural

direction of the hair. For the backside, start from the nape of the neck and go to the top

of the head (3), for the sides, from the ears to the top of the head (4) and for the top of

the head, from the forehead to the backside of the head (5).

 We recommend to do the hair regularly in order to check the homogeneity of the cutting

and to replace the hair. For the same reason, once the hair is cut and done, work the hair

clipper again but quicker in order to cut the hair that would have escaped from the first

cutting. You can eventually insist on the places with defaults.

OUTLINING

 Outlining requires no attachment combs. Take the clipper and push the lever (see next

paragraph) up to the close-cut position.

 Comb hair into the required style. Start from the outline of the ear by placing the side of

the hair clipper on the skin and following the roundness of the ear (6). To draw the

sideburns and the nape of the neck, place the hair clipper in the wrong side (with the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team HCS 2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team HCS 2 Manual

Product: