487004

Team HC 19 R Manual

13
Zoom out
Zoom in
Previous page
1/51
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
13
TEAM HC 19 R - 110518
Assembly page 13/51
Fax +32 2 359 95 50
• For the front of the crown, cut the hair against the direction in which it grows. Then even it
up with the sides (15).
• To taper hair down to the neckline, use attachment comb in position “1”. Comb hair,
check for uneven spots and outline sideburns and neckline (16).
CUTTING WITHOUT THE COMB ATTACHMENT
Remove the comb attachment if you want to cut hair to a length of 1mm. To cut the hair with
the help of a comb or your fingers as well as to cut the outlines, you do not need the comb
attachment.
• Push the sliding lock switch to the unlock position.
• Take off the comb attachment by pulling it holding it by the sides (see page 2, B 6 and 7).
Cutting hair with the help of a comb or your fingers
Remove the comb attachment carefully, as explained in the previous paragraph.
Raise a wisp of hair with the help of the comb (17), or take the wisp between your fingers (18).
Take the wisp through the comb or fingers until only the desired hair length remains under the
comb/fingers. Cut the hair that is above the comb or fingers with the hair clipper (19 and 20).
Cutting hair with the integrated thinning function
The thinning function allows you to thin out your hair at some places to change the volume of
the hair cut.
• Push the switch upwards to the “THINNING” position.
• Take the wisp through the comb or fingers until only the desired hair length remains under
the comb/fingers and cut the hair that is above the comb or fingers with the hair clipper.
Outlining
• Outlining requires no attachments.
• Comb hair into the required style. Position clipper between the sideburns and the ear. Make
sure the outer edge of the blade is against the hairline. With the outline of the hair as your
guide, slowly move the clipper around the ears (12). For the back of the neck and the
sideburns, hold the clipper upside down (13), and move downwards holding it against the
skin at the length desired.
CUTTING A BEARD
• Lead the appliance against the grain of the beard.
• Comb the beard hair with the supplied comb so that it stands as high as possible, all in the
same direction.
• Put the comb attachment on the appliance and slide it to the desired cutting setting.
• Switch on the appliance (“CUT” position) and cut the beard.
Cutting the outlines of the beard
• Remove the comb attachment from the appliance.
• Hold the appliance in diagonal position with the front side pointing away from you.
• Start with the chin and cut backwards.
• Follow the chin line and cut the longer hair at the outside of the beard.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 19 R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 19 R in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info