401510

Team hc 17 r Manual

11
Zoom out
Zoom in
Previous page
1/56
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
11 TEAM HC 17 R - 091125
Assembly page 11/56
Fax +32 2 359 95 50
When you decide to throw away the appliance, make sure to remove the battery and to
dispose of it in an ecological manner. For more information contact your town authorities.
BE CAREFUL NOT TO TOUCH THE ACCUMULATOR OR THE LEAKING LIQUID.
(*)
Competent qualified electrician: after-sales department of the producer or importer or any
person who is qualified, approved and competent to perform this kind of repairs in order to
avoid all danger. In case of need you should return the appliance to this electrician.
CONNECTING
The charging base can be connected to any voltage outlet - even to shaver sockets -
between 230-240 volts ac (-).
Place the rechargeable hair clipper, facing the front onto the charging base.
The red charge indicator will light up, when the power unit is inserted on the plugged-in
charging base.
The hair clipper may warm up somewhat during recharging. This has no significance on the
unit's operation. Overcharging is impossible.
To maintain the hair clipper's full performance, it should always be stored on the charging
base after use.
PRESERVING THE RECHARGEABLE BATTERY
To maximise the capacity and life of the rechargeable battery, it should be fully charged for 16
hours before the first use and then fully discharged by using. Then recharge to full capacity (6
hours). This discharging/charging procedure should be done every six months.
BEFORE YOU START
Make sure that your clipper is clean, properly oiled and in perfect working condition.
Caution: if the blade is not oiled correctly, the appliance will not work properly.
Place a towel around the neck of the person whose hair is to be cut to prevent hair from
falling inside the collar.
Have the person sit on a chair so that his/her head is at your eye’s level.
Comb the hair thoroughly and hold the clipper in a relaxed, comfortable grip. This will help
you maintain an accurate cutting control.
OIL (see page 2: A)
To maintain your clipper in peak condition, the blades should be oiled every few haircuts. Do
not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will evaporate
and leave the thick oil which may slow down the blades' motion.
MOUNTING (see page 2: B)
To mount the comb attachment, put the locking knob in position (see page 3, E 24)
and insert the comb attachment as described on page 2, B. The "clicks" that you can hear
correspond to the different cutting length settings. Once the comb attachment stops, it
means that it is in position "1".
To remove the comb attachment, proceed the other way around, still making sure that
the locking knob is in position.
Once you have chosen the cutting length, put the locking knob in position to block the
comb attachment.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team hc 17 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team hc 17 r in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info