487001

Team HC 14 RCE Manual

11
Zoom out
Zoom in
Previous page
1/40
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
11
Assembly page 11/40
Fax +32 2 359 95 50
MOUNTING (see Page 2: B)
To mount the comb attachment, put the locking knob in position (see page 3, E, 25)
and insert the comb as described on page 2, B. The "clicks" that you can hear correspond
to the different cutting length settings. Once the comb stops, it means that it is in
position"1".
To remove the comb attachment, proceed the other way around, still making sure that
the locking knob is in position.
Once you have chosen the cutting length, put the locking knob in position to block the
comb.
To attach the comb, hold it with teeth up and snap comb attachment firmly to the appliance.
The comb attachment can be set to 7 cutting length positions:
1. 1/6"
2. 1/4"
3. 1/3"
4. 5/12"
5. 1/2"
6. 7/12"
7. 2/3"
CUTTING HAIR WITH THE COMB ATTACHMENT (SEE PAGE 2: C and PAGE 3)
Only cut a small amount of hair to start with until you become accustomed to the length
the comb attachment gives to the hair.
We suggest you try the longest comb attachment in position “7” on the clipper first.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The
clipper works most efficiently when it works at its own speed.
Start by combing the hair in its natural direction.
Place the comb attachment in position “7” to your clipper and start by trimming the sides
from the bottom upwards. Hold the clipper lightly against the hair with the teeth of the
comb attachment pointing up but flat against the head. Slowly lift the clipper up and
outward through the hair, cutting only a small amount at a time (8 and 9).
If you want shorter hair, either place the comb attachment in position “1” or change the
hair length (see B, 6). You can also apply more pressure to the present comb attachment.
This procedure requires practice, and it is always better to leave too much hair during the
first few haircuts (10).
For the top of the head, you will give a fairly short cut if you place the comb attachment in
position “1”. With the teeth flat against the head, slowly start trimming from the front to the
back. Again, it is better to leave the hair longer at the beginning (11).
Short cuts
Always cut from the back of the neck to the crown, placing the comb attachment in
position “7”. Holding it flat against the head, slowly move the clipper up through the hair.
Use the same technique for the sides, cutting from the bottom to the upper side of the
head (14).
For the front of the crown, cut the hair against the direction in which it grows. Then even it
up with the sides (15).
To taper hair down to the neckline, use attachment comb in position “1”. Comb hair,
check for uneven spots and outline sideburns and neckline (16).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 14 RCE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 14 RCE in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info