487628

Teac AG-980 Manual

23
Zoom out
Zoom in
Previous page
1/136
Next page
23
ENGLISH
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult with
your dealer. Under no circumstances should you repair the receiver yourself as this could invalidate the warranty.
PROBLEME CAUSE POSSIBLE REMEDE
No power
No sound
Stations cannot be received
Preset stations cannot be received
Poor FM reception
Continuous hissing noise during FM
reception, especially when a stereo
broadcast is received.
Continuous or intermittent hissing
noise during AM reception, especial-
ly at night.
No recording
Remote control unit does not oper-
ate.
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet
is inactive.
• The speaker cords are disconnected.
• The volume is adjusted too low.
• The MUTING button on the remote control is
pressed to ON.
• Speakers are not switched on.
• Incorrect selection of the input source.
• Incorrect connections between the compo-
nents.
• No antenna is connected.
• The desired station frequency is not tuned in.
• The antenna is in wrong position.
• An incorrect station frequency has been memo-
rized.
• The memorized stations are cleared.
• No antenna is connected.
• The antenna is not positioned for the best
reception.
• Weak signals.
• Noise is caused by motors, fluorescent lamps
or lightning, etc.
• Incorrect selection between the components.
• Incorrect operation of each component for play-
back and recording.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
• Connect the cord securely.
• Check the outlet using a lamp or another appli-
ance.
• Check the speaker connections.
• Adjust the volume.
• Press the MUTING button to cancel the muting
effect.
• Switch on the desired speakers.
• Select the desired input source correctly.
• Make connections correctly.
• Connect an antenna.
• Tune in the desired station frequency.
• Move the antenna and retry tuning.
• Memorize the correct station frequency.
• Memorize the stations again.
• Connect an antenna.
• Change the position of the antenna.
•
Change the position of the antenna.
•
Install an outdoor antenna.
• Keep the receiver away from noise sources.
• Install an outdoor AM antenna.
• Make connections correctly.
• Operate each component correctly.
• Replace the batteries.
• Remove the obstacle.
Restoring factory settings
If you have made a lot of changes in the setup, and want to
restart from a known set of options, restore the unit to the
factory default settings as follows:
1. Turn the unit standby using the STANDBY/ON button.
2. While holding down the MAIN ZONE button, press the
STANDBY/ON button of the main unit.
All memories are erased, and the unit returns to the factory
settings.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teac AG-980 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teac AG-980 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info