487623

Teac A-R650 Manual

5
Zoom out
Zoom in
Previous page
1/64
Next page
5
ENGLISH
E
Speaker Connections
Caution:
To avoid damaging the speakers with a sudden high-level
signal, be sure to switch the power off before connecting the
speakers.
<
Check the impedance of your speakers. Connect speaker with
an impedance of 4 to 16 ohms when using only one pair of
speakers (SPEAKERS A or SPEAKERS B). When using two pairs
of speakers simultaneously, the impedance should be 8 to 16
ohms.
<
The black speaker terminals are _ (negative).
Generally, the + side of the speaker cable is marked to make
it distinguishable from the _ side of the cable. Connect this
marked side to the + terminal and the unmarked side to the
black _ terminal.
Caution:
The metal portions of the two separate wires should not touch
or an electrical short can occur. Shorted wires can create a fire
hazard or induce a failure in your equipment.
How to connect
Speakers A, B
1. Turn the terminal cap counterclockwise to loosen it. The speaker
terminal caps cannot be fully removed from the base.
2. Insert the wire into the terminal fully and turn the terminal cap
clockwise to securely connect it .
<
Make sure none of the wire insulation is under the terminal, only
the bare, stripped wire.
<
Make sure the wire is fastened firmly by pulling the cable lightly.
F
AC INLET
Use only the supplied power cord.
< Use of other power cord may result in fire or electric shock.
< Unplug the power cord when you are not going to use the unit
for long periods of time.
< Be sure to connect the power cord to an AC outlet which
supplies the correct voltage.
< Hold the power plug when plugging or unplugging the power
cord. Never pull or yank on the power cord.
A
PHONO jacks/SIGNAL GND terminal
Connect the turntable’s RCA pin cords to PHONO jacks. Make
sure to connect:
white plug q white jack (L: left channel)
red plug q red jack (R: right channel)
Connect the turntable’s ground cord to SIGNAL GND terminal.
B
AUDIO IN/OUT jacks
Analog 2-channel audio signal is input or output from these
jacks. Connect the component with commercially-available RCA
cables.
Make sure to connect:
white plug
q
white jack (L: left channel)
red plug
q
red jack (R: right channel)
C
REMOTE CONTROL jacks
If you have TEAC T-R650, TR-650DAB or CD-P650, connect the
REMOTE CONTROL jack (A or B) of each component by the
remote control cord (provided with the T-R650, T-R650DAB or
CD-P650).
D
AC Outlet (switched)
This outlet is active only when the unit is on.
Caution:
Make sure that the total power consumption of all equipment
connected to the outlet does not exceed 500mA or 100 watts.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teac A-R650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teac A-R650 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info