587255
13
Zoom out
Zoom in
Previous page
1/68
Next page
Setup
17. Cooling fan – make sure that this fan is not blocked off in a rack to prevent
overheating the system.
I/O Card Installation
I/O cards of different types may be installed in the X-48 simultaneously. For example, an
X-48 may have one analog card and one digital card installed, with independent I/O routing.
Each X-48 option card provides 24 channels of input and output.
You will need a medium size Philips screwdriver.
Power off and unplug the X-48 to avoid shock hazard.
If rack mounted, remove the X-48 from the rack to gain access to the top panel.
Analog Card
1. Remove the six screws holding on the top panel (there is one on the rear).
2. Remove the top panel and set it aside. You will see two black connectors, one
labeled SLOT1 and one labeled SLOT2. On the back of the X-48, there are two
blank panels, one labeled SLOT1 (1-24) and one labeled SLOT2 (25-48).
3. Remove the blank panel corresponding to the black connector where the I/O card
will be connected. For example, if you are installing an analog card for channels 1-
24, remove the blank panel for SLOT1.
4. Continue with this section to install an analog card. Otherwise skip to the next
section to install a digital card.
5. Connect the flat gray cable provided with the analog card to the appropriate slot
connector in the X-48.
6. Slide the analog card into the slot from the rear of the X-48. Near the black
connector on the card, you will see a screw hole. With the card slid all the way in,
under that hole is a chassis screw that must be removed then used to hold the rear of
the analog card in place.
7. Secure the analog card’s connector plate to the rear panel of the X-48 using the
screws you removed in Step 6.
8. Connect the other end of the flat gray cable to the black connector on the card.
9. Just behind the front panel you will find yellow/black/red cables with white
connectors. These are power cables for the analog card. Connect one of these to the
matching white connector on the analog card.
10. Replace the top panel.
Digital Card
1. Remove the six screws holding on the top panel (there is one on the rear).
2. Remove the top panel and set it aside. You will see two black connectors, one
labeled SLOT1 and one labeled SLOT2. On the back of the X-48, there are two
blank panels, one labeled SLOT1 (1-24) and one labeled SLOT2 (25-48).
3. Remove the blank panel corresponding to the black connector where the I/O card
will be connected. For example, if you are installing an analog card for channels 1-
24, remove the blank panel for SLOT1.
4. Connect the flat gray cable provided with the digital card to the appropriate slot
connector in the X-48.
5. Slide the digital card into the slot from the rear of the X-48.
13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam X-48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam X-48 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info