617924
39
Zoom out
Zoom in
Previous page
1/56
Next page
TASCAM MD-CD1MKIII 39
2 Press the RECORD button,
Over Write
will
be shown on the display, and the deck will enter
recording standby mode.
Adjust the recording level if necessary.
3 Press the PLAY button and overwrite recording
begins.
NOTE
When
SINGLE
,
RANDOM
or
PROGRAM
lights up in the
display, overwrite recording cannot be performed. In the
case of step 2 above,
Can't Rec
will be displayed.
Sync recording
The Sync recording function automatically begins
recording when the signal from external equipment is
present in the source input. Plus, if silence in the source
signal continues for more than four seconds, the deck is
automatically put into the recording standby mode.
Before following the procedure below, make sure that
basic recording preparations have been completed, a
recordable disc is inserted, and the deck is in stop mode.
1 Press the SYNC button on the remote control to
select on or off.
You can also switch the SYNC recording function
on or off using the
SYNC?
option on the REC sub-
menu of the MD menu.
2 Set the signal detection threshold level using the
SYNC LEVEL?
option on the REC sub-menu of
the MD menu. The level can be set from –72 dB to
–30 dB in 6 dB increments.
The default setting is –54 dB.
3 Press the RECORD button to enter recording
standby mode.
NOTE
In this status, recording will begin as soon as a source
signal is input.
4 Input the source signal.
When a source signal is detected, recording begins
automatically.
If the signal is under the threshold level for over four
seconds, the deck automatically enters recording
standby mode.
NOTE
During SYNC recording standby, recording cannot be
started manually by pressing the PLAY button.
5 To manually stop recording, press the STOP button.
NOTE
During SYNC recording, even if the
READY button
is pressed, the recording standby mode cannot
be entered. (The button cannot be used to pause
recording.)
The
INPUT SEL button does not function during SYNC
recording.
After SYNC recording finishes and the deck enters
recording standby mode, if the power is turned off the
recording data will be deleted. Make sure to press the
STOP button so that the U-TOC is written onto the disc
before turning the power off.
Checking remaining MD time
During MD recording or recording standby mode,
press the TIME button on either the front panel or the
remote control, and the elapsed track recorded time and
remaining recording time will be shown in succession on
the display.
Display indication Time display
No indication Elapsed track recorded time
REMAIN
only, or
TOTAL
and
REMAIN
will light up
Disc remaining time
Even if the power is turned off, the time settings will
be retained.
9 – MD recording from an external source
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam MD-CD1MKIII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam MD-CD1MKIII in the language / languages: English as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info