592593
4
Zoom out
Zoom in
Previous page
1/12
Next page
4 TASCAM IF-FW/DM Owner's Manual
OInstallation
Installing the IF-FW/DM
1. Remove the five screws holding the blank
plate or card currently installed in Slot 1
then remove the plate or card.
2. Insert the IF-FW/DM into Slot 1, mak-
ing sure that the card edges slide into the
white plastic guide inside Slot 1. Push it
all the way in until it clicks and the card
back plate is flush with the mixers back
panel. Excessive force is not required - if
it does not click in easily, remove it and
start again with attention to the guides.
3. Replace the five screws to hold the card in
place.
NOTE
The IF-FW/DM must be installed in to the
mixer’s Slot 1. It will not function in Slot 2.
The following installation must be done with
the mixer’s power OFF and disconnected.
There is a series of jumpers on the IF-FW/
DM that set its operating mode. These jump-
ers must be in the correct position to operate
with a DM-3200 or DM-24, which com-
municate with the IF-FW/DM via different
operating modes.
Early IF-FW/DM cards shipped configured
for the DM-24. From the time of DM-3200
software version 1.20 availability, IF-FW/
DM cards began shipping configured for the
DM-3200.
Please confirm your card’s configuration
with the following pictures and instructions
then make any necessary changes before
installing the IF-FW/DM into your mixer.
NOTE
The IF-FW/DM will not function if incor-
rectly configured for your mixer. Installing
an incorrectly configured card will not harm
anything.
The IF-FW/DM must be installed in either
mixer’s Slot 1. It will not function in Slot 2.
Use commonly available needle-nose pliers
to carefully change the configuration of the
card as shown.
Picture 1 is IF-FW/DM Configured for a
DM-3200. Note that jumpers J11 through
J43 are across pin rows 2 and 3.
Picture 2 is IF-FW/DM Configured for a
DM-24. Note that jumpers J11 through J43
are across pin rows 1 and 2.
Configure For Your Mixer
J11 - J43
SDT : 1-2 (default)
LVDS : 2-3
Card edge
U43
U42
U41
U40
U26
U25
U24
U23
U35
U34
U32
U31
U18
U17
U16
U15
U39
U38
U37
U36
U22
U21
U20
U19
U30
U29
U28
U27
U14
U13
U12
U11
1
2
3
3
2
1
For DM-24
Picture 2
J11 - J43
SDT : 1-2 (default)
LVDS : 2-3
Card edge
U43
U42
U41
U40
U26
U25
U24
U23
U35
U34
U32
U31
U18
U17
U16
U15
U39
U38
U37
U36
U22
U21
U20
U19
U30
U29
U28
U27
U14
U13
U12
U11
1
2
3
3
2
1
For DM-3200
Picture 1
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam if-fw dm FIRE WIRE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam if-fw dm FIRE WIRE in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info