617900

Tascam HS-P82 Manual

40
Zoom out
Zoom in
Previous page
1/64
Next page
40 TASCAM HS-P82
PreREC Time
Set the pre-recording time and ON/OFF settings. Turn this
function ON/OFF and set the time in seconds. (Default
setting:
OFF
)
To set the recording time, touch the knob. You can adjust
the value using the DATA dial. The range of setting values is
1–5 seconds. (Default value: 2 seconds)
Auto Marker
Make settings related to auto markers.
Audio Over: Use this to add markers when the set audio
level is detected. Turn this function ON or OFF. (Default
setting:
OFF
.)
To set the audio detection level in decibels, touch the
knob. You can adjust the value using the DATA dial. The
range of setting values is –0.2 dB to –0.03 dB. (Default
value: –0.2 dB)
Settings made here are reflected in the “Over Level”
setting on the METER SETUP screen.
Time Interval: Use this to add marks at fixed time intervals.
Turn this function ON or OFF and set the time interval.
(Default setting:
OFF
)
To set the time, touch the knob. You can adjust the value
using the DATA dial. The range of setting values is 1–10
minutes.
(Default value: 5 minutes)
Sync Unlock: Use this to add a mark when synchronization
with the master clock is lost. Turn this function ON or
OFF. (Default setting:
OFF
)
Playback settings (PLAY SETUP)
Play Mode
Set how the playback of takes is handled.
One Take: Only the currently selected take is played back.
All Take: All the takes in the currently loaded project are
played back.
(Default setting:
One Take
)
Sync and time code settings (SYNC T/C)
Use the
SYNC
T/C
screen to make synchronization and time
code settings. This screen has four pages:
CLOCK
,
TIME-
CODE
,
SETUP
and
I/O
. Touch the tabs at the bottom of the
screen to open the corresponding page.
CLOCK page
View various clock status information and select the clock
used for synchronization.
Select the master clock to use from the
MASTER
item
options.
INT (default value): Use this unit’s internal clock.
WORD: Synchronize with the word clock input through the
CASCADE/WORD/VIDEO IN connector.
VIDEO: Synchronize with the video clock input through the
CASCADE/WORD/VIDEO IN connector.
AES (1-2, 3-4, 5-6, 7-8): Synchronize with the clock of the
AES/EBU digital signal input through the DIGITAL I/O
connector.
You cannot select an input as the master clock if the
sampling rate converter is ON for that input.
NOTE
A check mark appears on the button of the currently active
•
master clock.
If synchronization from an external clock is interrupted,
•
the unit’s internal clock becomes active. In this case, a
check mark appears on the INT button to show that it has
become the active clock, and an “x” appears on the button
of the external clock that had been selected.
NOTE
The statuses of the digital input signals (AESx-x IN) are shown
in the STATUS item as follows.
When locked
"Locked (xx.xxxkHz)"
When sampling frequency conversion is ON
"Locked (xx.xxxkHz FsCnv)"
When unlocked
"Unlocked (xx.xxxkHz)"
When there is no signal
6 – Internal Settings and Operations
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-P82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-P82 in the language / languages: English as an attachment in your email.

The manual is 8,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info