617905
13
Zoom out
Zoom in
Previous page
1/72
Next page
TASCAM HS-8 13
PARALLEL connector
The PARALLEL connector on the rear panel allows external
control of this unit. The pin assignments are as follows.
Pin No. Function In/Out
1 GND
2 PLAY/Flash 1 In
3 STOP/Flash 2 In
4 RECORD/Flash 3 In
5 SKIP FWD/Flash 4 In
6 SKIP BWD/Flash 5 In
7 FLASH LOAD (STOP) In
8 FADER START In
9 FLASH Tally Out
10 READY Tally Out
11 RECORD Tally Out
12 STOP Tally Out
13 PLAY Tally Out
14 REMOTE Select In
15 PAUSE/Flash 6 In
16 CALL/Flash 7 InIn
17 AUX1/Flash 8 In
18 AUX2/Flash 9 In
19 AUX3/Flash 10 In
20 Flash Page In
21 Reserved
22 CF1 Tally Out
23 ONLINE Tally Out
24 CF2 Tally Out
25 +5V*
In: Command input, for transport control
Internal circuit, +5V pull-up
Operates with low commands of 50 msec or more
Out: Command output, for tally output
The internal circuit is open collector (output
impedance 10Ω)
Low command output when operating
20 V dielectric strength, 35 mA maximum current
*
+5V: 50 mA maximum supplied current
NOTE
The FLASH LOAD (STOP) (pin 7) functions are FLASH LOAD when
stopped and STOP during playback and when paused.
When Remote Select (Pin 14) is high, the input pins that have
two commands separated by a “/” (pins 2–6 and 15–19) in the
above table will perform the rst-listed function, and can be
used as conventional parallel controllers.
When this pin is low, the above-listed input pins will function as
ash start keys. Moreover, the key assignments will be as follows
according to the high/low state of pin 20.
#14 #20 Flash-start take
Low High 1–10
Low Low 11–20
The following example is of a connection that uses a fader to
start and stop playback of this device.
For information about the assignment of AUX1-3 (pins
17-19) functions, see the “PARALLEL tab” of the REMOTE
SETUP screen on page 48.
RS-232C Connector
The RS-232C connector on the rear panel can be
connected to an RS-232C connector on a computer to
allow control of this unit from that computer.
Makes settings related to communication on the REMOTE
SETUP screen RS-232C page. (See “RS-232C page on page
48.)
NOTE
Please contact TASCAM customer support for information about
this unit’s RS-232C command protocol.
RS-422 connector
You can control this unit remotely by connecting the
RS-422 connector on its rear panel to a controller or editor
compatible with SONY P2 protocol (RS-422).
Make settings related to operation on the REMOTE SETUP
screen RS-422 page. (See “RS-422 page” on page 48.)
NOTE
Please contact TASCAM customer support for information about
this unit’s protocol compatibility.
2 − Names and functions of parts
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-8 in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info