617909
28
Zoom out
Zoom in
Previous page
1/60
Next page
28
TASCAM DR-680MKII
4 – Recording
Connecting other equipment
Connect microphones and other external equipment as
shown in the figure below.
Microphones
Input settings
This unit has 6 analog mic/line inputs and a stereo digital
input.
6 tracks and a stereo track can be recorded for a total of 8
tracks.
The inputs recorded on the tracks are as follows.
Track Input
Tracks 1/2 Analog inputs 1/2
Tracks 3/4 Analog inputs 3/4
Tracks 5/6 Analog inputs 5/6 or digital input
Stereo track
Stereo mix of inputs 1–6 or digital
input
Set the recording source for the stereo track on
REC
page
of the
MENU
screen. (See “Stereo track recording settings”
on page 25.)
Setting the input sources
Use the INPUT switches on the top panel to set the type of
input for each track to either mic or line.
LINE: Set the switch to LINE when the line output jack of
an external device is connected to the analog input on this
unit.
MIC: Set this switch to MIC when a microphone is
connected to this unit.
Phantom power
This unit can supply +48 V phantom power to condenser
microphones.
Use the PHANTOM switches on the top panel to turn the
phantom power supply ON or OFF for mic input pairs 1/2,
3/4 and 5/6.
CAUTION
Phantom power is also supplied to the TRS pins of
the MIC/LINE INPUTS Jack. If you connect a line level
device while phantom power is being supplied, that
device and this unit could be damaged.
Confirm that phantom power is OFF before connecting
a line level device to a MIC/LINE INPUTS jack. If you
connect a line level device while phantom power is
being supplied, that device and this unit could be
damaged.
Do not connect or disconnect mics when a PHANTOM
switch is set to ON. Doing so could cause a loud
noise and might damage this unit and connected
equipment.
Set the PHANTOM switch to ON only when using a
condenser microphone that requires phantom power.
Turning phantom power on when a dynamic mic or
other mic that does not require it is connected could
damage this unit and connected equipment.
When using condenser mics that require phantom
power and dynamic mics together, be sure to use
balanced dynamic mics. Unbalanced dynamic mics
cannot be used when phantom power is enabled .
Supplying phantom power to some ribbon mics will
break them. If you are unsure, do not supply phantom
power to a ribbon mic.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam DR-680MKII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam DR-680MKII in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info