617894
49
Zoom out
Zoom in
Previous page
1/104
Next page
TASCAM DP-32 49
7 - Recorder Functions
Punching in and out
Punching in/out is a technique used to replace a part of
an already recorded track.
Start playback and when you reach the part that you want
to replace, switch to record (punch in), then switch back
to playback (or stop) when you finish replacing the part
that you want (punch out).
1. Decide what part of the track you plan to re-record.
Choose a point to begin where the new recording can
sit well with the existing recording.
2. Press the REC buttons of the tracks that you want
to partially re-record to put them into recording
standby (REC buttons start flashing).
3. Start playback before the part you want to replace.
4. When the part you want to replace is reached,
press the RECORD (0) button and start your
performance.
Recording starts (punch in).
5. When you finish the replacement recording, press
the PLAY (7) button.
Playback resumes (punch out).
TIP
You can also press the STOP (8 ) button to punch out at the
end of the replacement recording.
Using a footswitch to punch in/out
You can connect a TASCAM RC-3F footswitch (sold
separately) to the REMOTE jack on the front panel and
use it to punch in and out.
In step 4 above, step on the footswitch instead of
pressing the RECORD (0) button, and in step 5, step on
the footswitch again instead of pressing the PLAY (7)
button.
TASCAM RC-3F footswitch
(sold separately)
NOTE
Step on the switch (pedal) that you have set to
PUNCH IN/
OUT
in the footswitch settings. By default, the center pedal
is set to
PUNCH IN/OUT
. (See "Setting the footswitch"
below.)
Setting the footswitch
Set the footswitch on the
PREFERENCE
screen.
1. When the recorder is stopped, press the MENU
button to open the
MENU
screen.
2. Use the JOG/DATA dial or the CURSOR (5/b/g/t)
buttons to select (highlight green)
PREFERENCE
,
and then press the F4 (t) button.
The
PREFERENCE
screen opens.
3. Use the CURSOR (5/b) buttons to select (highlight
blue)
Foot SW Right
.
4. Use the JOG/DATA dial to select the function
that you want to assign to the right pedal of the
TASCAM RC-3F footswitch.
Options:
PLAY
,
REC
,
STOP
,
FF
,
REW
,
PUNCH IN/OUT
,
PLAY/STOP
(right pedal
default),
CUE LOCATE
5. In the same way, set
Foot SW Center
for the
function of the center pedal and
Foot SW Left
for the left pedal.
Options:
PLAY
,
REC
,
STOP
,
FF
,
REW
,
PUNCH IN/OUT
(center pedal default),
PLAY/
STOP
,
CUE LOCATE
(left pedal default)
6. After making the settings, press the HOME button
to return to the Home screen.
ª
Footswitch function list
Function Description
PLAY
Same as unit's
PLAY (7) button
REC
Same as unit's
RECORD (0) button
STOP
Same as unit's
STOP (8) button
FF
Same as unit's
F FWD (,) (TO LAST REC)
button
REW
Same as unit's
REW (m) (TO ZERO) button
PUNCH IN/
OUT
Punches in when pressed during playback,
punches out when pressed during recording.
PLAY/STOP
Starts playback when stopped, stops in other
states.
CUE LOCATE Locates last point where playback started.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam DP-32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam DP-32 in the language / languages: English as an attachment in your email.

The manual is 10,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info