587263
26
Zoom out
Zoom in
Previous page
1/44
Next page
26 TASCAM CD-RW901MKII
Before you start recording using the CD-RW901MKII, make
sure that you understand the following key points:
Once you have recorded on a CD-R disc, the data cannot
be erased from it.
You can add tracks to an unfinalized recordable disc.
Once finalized, a CD-R disc is “fixed” and behaves in
the same way as a pre-recorded disc. Finalized CD-RW
discs, however, can be erased, refreshed and re-recorded.
Input monitoring
When the unit is in record ready, or record mode, the input
signal is output from the OUT jacks (digital and analog),
allowing you to hear the input signal.
Press the RECORD key on the front panel or the remote
control when a recordable disc is not inserted.
The word Monitor appears on the display to show that the
output signal is an echo of the input signal(s).
Exit the monitor mode by using the STOP key.
Frequency conversion
The sampling frequency for CDs is 44.1 kHz. The
CD-RW901MKII will always record (and play back) CDs at
this frequency.
However, if recording through a digital connection (coaxial,
optical or AES/EBU) and the source has been recorded at a
frequency other than 44.1 kHz, or is being played back at a
non-standard speed using a varispeed unit (more than 1%
away from the standard), the CD-RW901MKII’s internal
frequency converter: SRC (Sampling Rate Convertor) will
automatically convert the incoming frequency to 44.1 kHz.
To enable the SRC
Press the MENU key and select the SRC? option in the REC
sub-menu (see “Operation basics” on page 16). Rotate the
MULTI JOG dial to select ON. Press the MENU key or push
the MULTI JOG dial to enter.
NOTE
When the SRC function is off, and a digital signal is
received, the display shows the REC indicator flashing
while recording or when in recording standby mode.
The digital signals other than 44.1kHz cannot be
recorded when SRC is off. The error message Not
F s 4 4 .1 k! will appear on the display.
Input selection
To select the input to be recorded, press the INPUT SELECT
key on the main unit.
Repeated presses of the key cycle through the following
options:
ANALOG
Balanced/Unbalanced
OPTICAL
Optical digital in
COAXIAL
Coaxial digital in
AES/EBU
AES/EBU digital in
In the case of either the coaxial or optical inputs being
selected, the indicator COAXIAL or OPTICAL lights up.
If the balanced analog signal is selected, the ANALOG indicator
blinks. If the unbalanced analog signal is selected, the ANALOG
indicator lights up.
When the digital input AES/EBU is selected, there is no indicator
lights up, instead, the word AES/EBU will appear on the
screen for a while.
Analog recording level:
The level of the analog signals received at the ANALOG IN
jacks are controlled with the INPUT (L.R) controls. When
recording analog signals, set the digital volume to 0 dB.
Digital recording level:
The level of the digital signal may be controlled using the
digital volume menu, as described below.
1. Call up the VOLUME option in the REC sub-menu
(see “Operation basics” on page 16).
Push the MULTI JOG dial to enter the function on.
2. Rotate the MULTI JOG dial to adjust the input
volume between -54dB and +18 dB (relative to the
original input level).
There is also a -‹ setting which represents a complete
signal cut. The display shows Vol> ---dB for the
-‹ setting.
3. Press the MENU key or push the MULTI JOG dial to
enter the setting and return to normal mode.
5 − Recording
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam CD-RW901MKII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam CD-RW901MKII in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info