587258
33
Zoom out
Zoom in
Previous page
1/40
Next page
TASCAM CD-500/500B 33
For details about using the CONTROL I/O PARALLEL
connector, see “Using the parallel connector (CD-500B
only)” on page 33.
Event start
ª
Using the CONTROL I/O START (RELAY IN)
connector
Wire the event output connector of another device with a
3.5-mm miniplug, and connect that 3.5-mm miniplug to
the CONTROL I/O START (RELAY IN) connector on the
rear panel of this unit.
Then, set the
06 RELAY
menu item to
ON
.
ª
Using the CONTROL I/O PARALLEL
connector [CD-500B only]
With the CD-500B, when stopped or paused, playback
can be started by inputting a one-shot pulse signal from
outside. Input a one-shot pulse (active low, 30 ms or
longer) through pin 13 of the CONTROL I/O PARALLEL
connector.
Using the RS-232C connector
The CONTROL I/O RS-232C connector (D-sub 9-pin, RS-
232C compliant) can be used for serial control of this unit
by a computer or other external device.
Setting the baud rate
Use the
13 232C
menu item to set the baud rate.
Select
96
(9600 bps, default value),
19 2
(19200 bps) or
384
(38400 bps).
For further details, please contact TASCAM customer
support.
NOTE
The baud rate setting is retained even when the power is
turned off.
Restoring factory default settings
You can restore the unit to factory default settings that
are stored in the backup memory. The following default
settings are stored in the backup memory
Playback mode
Playback time display mode
Auto-ready function on/off
Auto-cue function on/off
Repeat function on/off
Various menu settings (original key, eject block, auto-
cue level, program, fade in/out, relay playback, power
on play, mono output, resume, EOM time, incremental
playback, pitch step, RS232C baud rate, skip back,
remote control receipt, interval time, frame display,
foot switch, user data, parallel mode)
To restore all settings to their factory defaults
1 Select the
20 RESET
menu item.
2 Press the PITCH [MENU] knob.
-SURE-
blinks on the display.
3 Press the PITCH [MENU] knob on the main unit or
the ENTER button on the remote control to restore
the settings to the factory defaults stored in the
backup memory and exit menu mode.
The display returns to ordinary disc and track
information.
Checking the firmware version
To check the firmware version, use the
21 INFO
menu
item.
1 Select the
21 INFO
menu item.
2 Press the PITCH [MENU] knob on the main unit or
the ENTER button on the remote control to show
the system firmware version on the display.
Version Build number
3 Press the PITCH [MENU] knob on the main unit or
the ENTER button on the remote control again to
return to menu item selection.
7 – Other Functions
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam CD-500B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam CD-500B in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info