587257
34
Zoom out
Zoom in
Previous page
1/40
Next page
34 TASCAM CD-500/500B
User data settings (CD-500B only)
You can set whether or not a USER DATA BIT is output
with the digital output from the DIGITAL OUT (AES/EBU)
connector. To set output of the USER DATA BIT, use the
22
U-DATA
menu item (default value:
ON
).
NOTE
If the signal output from this connector does not play
back correctly, set this item to
OFF
.
The user data setting is retained even when the power
is turned off.
Using the parallel control
(CD-500B only)
Using the CONTROL I/O PARALLEL connector, you can
use external parallel control to operate this unit. Two
types of parallel control (normal mode and direct play
mode) can be used with this unit. To set parallel control,
use the
23 PARALL
menu item.
Options:
1
Normal mode (default)
In addition to starting, stopping and skipping, fader
start/stop are controlled.
2
Direct play mode
Tracks 1–20 can be played directly.
The pin assignments are as follows
Pin
No.
Function
IN/OUT
MODE: 1 MODE: 2
1 STOP Tally
OUT
2
SKIPBack Select: 1
IN
3
SKIPForward Select: 2
IN
4 NO DISC Tally
OUT
5 EOM
OUT
6
SEARCHBack Track Play: 1*
IN
7
SEARCHForward Track Play: 2*
IN
8 GND
9 PLAY Tally
OUT
10 PAUSE Tally FLASH LOAD Tally*** OUT
11
FADER STARTSTOP Track Play: 3*
IN
12 STOP
STOPFLASH LOAD**
IN
13 PLAY
Track Play: 4*
IN
14 PAUSE
Track Play: 5*
IN
15 +5V
IN: active low external command reception (operates
when ground 30 ms or longer)
OUT: signal for the display of transport status by open
collector (maximum voltage 15 V, maximum current 50
mA)
+5V: maximum supplied current 50 mA
* Track Play 1–5: plays the designated track. The track
played depends on the combination of Select: 1 (Pin
2) and Select: 2 (Pin 3) High (1) and Low (0) settings as
shown below.
** When stopped and the flash start function is on, if the
track beginnings have not yet been loaded, loading
starts. When playing back, playback stops.
*** When the flash start function is on, if the track
beginnings have been loaded completely, High (1)
results. If the track beginnings have not yet been loaded,
or are in the process of loading, Low (0) results.
Pin
No.
Mode 2
function
Select 1 and 2 combination
2 Select: 1 0 0 1 1
3 Select: 2 0 1 0 1
6 Track Play: 1 Track 1 Track 6 Track 11 Track 16
7 Track Play: 2 Track 2 Track 7 Track 12 Track 17
11 Track Play: 3 Track 3 Track 8 Track 13 Track 18
13 Track Play: 4 Track 4 Track 9 Track 14 Track 19
14 Track Play: 5 Track 5 Track 10 Track 15 Track 20
NOTE
The parallel mode setting is retained even when the
power is turned off.
7 – Other Functions
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam CD-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam CD-500 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info