415747
5
Zoom out
Zoom in
Previous page
1/12
Next page
4
5
Loudspeakers need power signals to produce acoustic energy when reproducing music. The range of electrical currents passing down
the cable from the amplifier to the loudspeaker is very wide. In decibel terms this is called the dynamic range. Modern loudspeakers
are capable of resolving a dynamic range of at least 80dB with a suitable power amplifier.
An 80dB dynamic range corresponds to voltages of between 50 Volt and 0.005 Volt at the loudspeaker terminals or equivalent currents
of between 0.0006 and 6 Amp. This is a truly wide range of electrical signals to pass down one cable without some interactions causing
a loss of resolution in the very small signals.
When electricity passes down a wire or cable, what goes in at one end is unfortunately different from what comes out at the other.
The degree of loss or modification of a signal depends on the physical characteristics of the cable and the nature of the signal. Heavy
electrical currents flowing down thin conductors cause heating effects.Very high frequency signals passing along conductors or cables
of certain lengths cause electromagnetic radiation effects (aerials). Electrical cables are selected for minimum loss and maximum
information resolution considering the type of electrical signals they are designed to carry.
A good solution to the problem is to 'bi-wire' the loudspeakers to the amplifier. This means providing two separate sets of cables from
the power amplifier to each loudspeaker and dividing the electrical signals into high current, 'slow' signals and light current, 'fast' signals.
Of course, the loudspeaker must be fitted with two pairs of terminals to take the two sets of cables; your Tannoy loudspeakers are of
course equipped for just this type of connection.
Bi-Wiring Theory
Bi-wiring releases the full potential of the Tannoy Prestige loudspeakers. Two complete sets of cable are required.
Switch the amplifier off. Deal with each 'side' of the system separately. Label two of the cables Left LF and Left HF (low frequency
and high frequency).
Label two of the cables Left LF and Left HF (low frequency and high frequency). Do the same for the right pair. Undo the loudspeaker
terminals, remove and retain the Bi-wiring links so that the same polarity terminals are no longer joined.
It is essential to get the polarity correct. If your amplifier does not have separate output terminals for bass and treble then, at the amplifier
end of the cable, connect the Left LF+ and HF+ cables together. Then wire to the amplifier Left channel positive terminal marked +
(plus) or coloured red.
Connect the Left LF - and HF - cables together to the amplifier negative terminal marked - (minus) or black.
Note the polarity marking on the cable. At the loudspeaker end connect the cables marked Left LF+ and LF- to the appropriate left
speaker LF terminals. Connect the Left HF+ and HF- to the appropriate + and - left speaker HF terminals.
Make the same connections with the Right LF and HF cables.
For optimum performance, the earth connection on the terminal panel should be connected to the amplifier chassis earth or other
ground point. This screening effect can give an improvement in detail clarity, depending on the amplifier used. Optimum results are
achieved using a screened loudspeaker cable designed for such a system, such as the Tannoy TLC.
Switch on the amplifier with the volume turned down. Select a favourite source and carefully turn up the volume. Check that bass and
treble sounds come from both speakers. If not, switch off and remake the connections.
Bi-Wiring
L
POWER AMPLIFIER
+
R
- + -
LINKS REMOVED
'EARTH' CONNECTION
ON AMPLIFIER (OPTIONAL)
TO 'GROUND' OR
TO RIGHT
SPEAKER
SINGLE WIRE MODE BI-AMPING MODE
BI- WIRE MODETERMINAL PANEL
FIG. 1 FIG. 2
FIG. 3 FIG. 4
-
+
-
+
L
POWER AMPLIFIER
LOW FREQUENCY
POWER AMPLIFIER
HIGH FREQUENCY
L
+
R
- -+
R
HIGH FREQUENCY
NEGATIVE(-) TERMINAL
LOW FREQUENCY
NEGATIVE(-) TERMINAL
HIGH FREQUENCY
POSITIVE(+) TERMINAL
'EARTH' OR 'GROUND' TERMINAL
LOW FREQUENCY
POSITIVE(+) TERMINAL
POWER AMPLIFIER
-+
L
+ -
R
ON AMPLIFIER (OPTIONAL)
TO 'GROUND' OR
'EARTH' CONNECTION
TO RIGHT
SPEAKER
LINKS REMOVED
AMPLIFIER (OPTIONAL)
ON HIGH FREQUENCY
'EARTH' CONNECTION
TO 'GROUND' OR
TO RIGHT
SPEAKER
TO RIGHT
SPEAKER
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tannoy turnberry he at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tannoy turnberry he in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info